Physics, 03.03.2020 05:47 oliviajewelwilliams

Under what circumstances are two circuits considered equivalent? A. their input values are the same B. the output of one is the inverse of the output of the other C. their output values are the same for all possible input combinations D. their output values are always 1 E. the input of one matches the output of the other

Answers: 3

Show answers

Answers

Answer from: lizzoone

B the output of one is the inverse of the output of the other

Explanation:

equivalent circuit refers to a theoretical circuit that retains all of the electrical characteristics of a given circuit. Often, an equivalent circuit is sought that simplifies calculation, and more broadly, that is a simplest form of a more complex circuit in order to aid analysis. In its most common form, an equivalent circuit is made up of linear, passive elements. However, more complex equivalent circuits are used that approximate the nonlinear behavior of the original circuit as well. These more complex circuits often are called macromodels of the original circuit. An example of a macromodel is the Boyle circuit for the 741 operational amplifier.

tutorialspoint

Network Theory - Equivalent Circuits

Advertisements

Previous Page Next Page

If a circuit consists of two or more similar passive elements and are connected in exclusively of series type or parallel type, then we can replace them with a single equivalent passive element. Hence, this circuit is called as an equivalent circuit.

In this chapter, let us discuss about the following two equivalent circuits.

Series Equivalent Circuit

Parallel Equivalent Circuit

Series Equivalent Circuit

If similar passive elements are connected in series, then the same current will flow through all these elements. But, the voltage gets divided across each element.

Consider the following circuit diagram.

Series Equivalent Circuit

It has a single voltage source (VS) and three resistors having resistances of R1, R2 and R3. All these elements are connected in series. The current IS flows through all these elements.

The above circuit has only one mesh. The KVL equation around this mesh is

VS=V1+V2+V3

Substitute V1=ISR1,V2=ISR2 and V3=ISR3 in the above equation.

VS=ISR1+ISR2+ISR3

⇒VS=IS(R1+R2+R3)

The above equation is in the form of VS=ISREq where,

REq=R1+R2+R3

The equivalent circuit diagram of the given circuit is shown in the following figure.

Equivalent Circuit

That means, if multiple resistors are connected in series, then we can replace them with an equivalent resistor. The resistance of this equivalent resistor is equal to sum of the resistances of all those multiple resistors.

Answer from: Quest

iron would move it is magnetic there is a mag field around the current in the wire

Answer from: Quest

Ithink the answer would be 1,350!

Another question on Physics

Physics, 22.06.2019 12:30

As part of your daily workout, you lie on your back and push with your feet against a platform attached to two stiff springs arranged side by side so that they are parallel to each other. when you push the platform, you compress the springs. you do an amount of work of 79.0 j when you compress the springs a distance of 0.230 m from their uncompressed length. (a) what magnitude of force must you apply to hold the platform in this position? (b)how much additional work must you do to move the platform a distance 0.230 m farther? (c) what maximum force must you apply to move the platform a distance 0.230 m farther?

Answers: 1

Answer

Physics, 22.06.2019 14:10

Click the game tab at the bottom of the simulation and select level 1. (there is no seesaw balance for this part of the activity.) balance the first equation, and click check to see if you got it right. if you can’t balance it in the first try, you can try again. work through the five equations for level 1. click continue to go on to level 2, and later level 3. each level is more difficult than the one before. keep trying until all the equations are balanced. in one or two sentences, describe how you did in the balancing game. in a few more sentences, explain one strategy you learned for balancing more complex equations.

Answers: 2

Answer

Physics, 22.06.2019 16:40

Aparticle's position is given by x = 3.00 - 9.00t + 3t2, in which x is in meters and t is in seconds. (a) what is its velocity at t = 1 s? (b) is it moving in the positive or negative direction of x just then? (c) what is its speed just then? (d) is the speed increasing or decreasing just then? (try answering the next two questions without further calculation.) (e) is there ever an instant when the velocity is zero? if so, give the time t; if not, answer "0". (f) is there a time after t = 3 s when the particle is moving in the negative direction of x? if so, give the time t; if not, answer "0".

Answers: 3

Answer

Physics, 22.06.2019 19:50

An air-filled capacitor is formed from two long conducting cylindrical shells that are coaxial and have radii of 26 mm and 103 mm. the electric potential of the inner conductor with respect to the outer conductor is - 700 v (k = 1/4πε 0 = 8.99 × 109 n · m2/c2) the energy stored in a 1.0-m length of this capacitor is closest to

Answers: 1

Answer

You know the right answer?

Under what circumstances are two circuits considered equivalent? A. their input values are the same...

Questions