Mathematics, 04.08.2019 15:00 1846252

The length of roberts rectangular deck is 4 feet less than twice the width, w. robert plans to increase all sides of the deck by 6 feet. write the equation for the area of he larger deck

Answers: 1

Show answers

Another question on Mathematics

Mathematics, 21.06.2019 18:30

Which number line represents the solution set for the inequality -1/2x> 24?

Answers: 2

Answer

Mathematics, 21.06.2019 20:30

What is 1/3x5 on anuber line what does it look like on a number line

Answers: 3

Answer

Mathematics, 21.06.2019 21:00

The measure of angle 0 is 600 degrees

Answers: 1

Answer

Mathematics, 21.06.2019 21:00

Graph the equationy=x^2 -[tex]y = x^{2} - 2[/tex]

Answers: 1

Answer

You know the right answer?

The length of roberts rectangular deck is 4 feet less than twice the width, w. robert plans to incre...

Questions

Engineering, 13.09.2019 23:10

Acarbon/epoxy (as/3501) unidirectional laminate with a fiber orientation q = 30° is exposed to the following stresses, sx = 40 ksi, sy = -20 ksi, txy...

Engineering, 13.09.2019 23:10

Abody is moving with simple harmonic motion. it's velocity is recorded as being 3.5m/s when it is at 150mm from the mid-position and 2.5m/s when 225mm...

Engineering, 13.09.2019 23:10

Acylinder, closed by a piston, has a volume of 0.03m and contains air at 1 bar and 15°c. the air is compressed isentropically to one quarter of its or...

Engineering, 13.09.2019 23:10

One way to lower nox emissions in diesel engines is to add water to the fuel. since water is not mixable with diesel fuel, it has to been emulsified b...

Engineering, 13.09.2019 23:10

For a body moving with simple harmonic motion state the equations to represent: i) velocity ii) acceleration iii) periodic time iv) frequency v) on a...

Engineering, 13.09.2019 23:10

The boiler pressure is 38bar and the condenser pressure 0.032 bar. the saturated steam is superheated to 420 oc before entering the turbine. a) calcul...

Engineering, 13.09.2019 23:10

How much heat (btu) is prod uced by a 150-w light bulb that is on for 20-hours?...

Engineering, 13.09.2019 23:10

The force vector of the quadriceps muscle group is oriented at 25 degrees to the mechanical axis of the tibia, and intersects the mechanical axis of t...

Engineering, 13.09.2019 23:10

Assuming that the quadriceps force vector has a magnitude of 1200 n, what turning force do the quadriceps muscles apply to the shank? show your wok...

Engineering, 13.09.2019 23:10

Athin rectangular plate having a width w and a height h is located so that it is noenal to a moving stream of fluid. assume the drag d, that the fluid...

Engineering, 13.09.2019 23:10

2.4 kg of nitrogen at an initial state of 285k and 150 kpa is compressed slowly in an isothermal process to a final pressure of 600 kpa. determine the...

Engineering, 13.09.2019 23:10

Given the latent heat of fusion (melting) and the latent heat of vaporisation for water are δhs = 333.2 kj/kg and δhv = 2257 kj/kg, respectively. use...

Engineering, 13.09.2019 23:10

Logarithmic decrement. assume the damping for the mass-springdamper system in the previous problem is unknown. if the amplitude decreases by 80% every...

Engineering, 13.09.2019 23:10

Asquare aluminum plate 5 mm thick and 200 mm on a side is heated while vertically suspended in quiescent air at 40ºc. determine the average heat trans...

Engineering, 13.09.2019 23:10

Cutting speed is determined by the surface velocity of the tool. a) true b) false...

Engineering, 13.09.2019 23:10

Ablock of ice weighing 20 lb is taken from the freezer where it was stored at -15"f. how many btu of heat will be required to convert the ice to water...

Engineering, 13.09.2019 23:10

Anatural gas fuel consists of the following volumetric composition: methane, ch4: 92.5 % ethane, c2h6: 3.7 % propane, c3h8: 0.8 % nitrogen, n2: 3...

Engineering, 13.09.2019 23:10

Nitrogen gas is compressed in a polytropic process (n=-1.8). the initial temperature and pressure are 285 k and 150 kpa, respectively. the initial vol...

Engineering, 13.09.2019 23:10

Using the data below, calculate the minimum number of teeth on pinion: *remember that for teeth to round up any decimals to the nearest integer. gear...

Engineering, 13.09.2019 23:10

An operating gear box (transmission) has 350 hp at its input shaft while 250. hp are delivered to the output shaft. the gear box has a steady state su...

More questions: Mathematics Another questions