Mathematics, 02.01.2020 13:31 dej33

Which is a irrational number, √39, √9, √49, 1.7

Answers: 3

Show answers

Another question on Mathematics

Mathematics, 21.06.2019 17:30

10 ! in a race, nick is 50 feet in front of jay after ten seconds. how fast can nick run, if jay can run 20 feet per second?

Answers: 1

Answer

Mathematics, 21.06.2019 18:30

Alicia puts $400 in a bank account. each year the account earns 5% simple interest. how much money will be in her bank account in six months?

Answers: 1

Answer

Mathematics, 21.06.2019 18:40

Valentina is subtracting from . she finds the lcd to be 15y2. what is valentina's next step?

Answers: 2

Answer

Mathematics, 21.06.2019 18:40

Acircle has a circumference of 28.36 units what is the diameter of the circle

Answers: 2

Answer

You know the right answer?

Which is a irrational number, √39, √9, √49, 1.7...

Questions

Engineering, 14.09.2019 02:10

Determine ixx for the cylinder with a concentarted circular hole. the mass of body is m...

Engineering, 14.09.2019 02:10

Two 14.5° pressure angle, mating, 5-pitch gears have 30 and 110 teeth. in practice, the gears are mounted at a center distance 0.7 inches greater than...

Engineering, 14.09.2019 02:10

The center distance of two spur gears that have 20° pressure angle and full-depth with diametral pitch of 8 teeth/in, is increased by 0.05 in over the...

Engineering, 14.09.2019 02:10

Two meshing 24-pitch, 25° pressure angle gears have n1-24 and n2 60 teeth. the in use center distance of the two gears is 0.16 inches larger than the...

Engineering, 14.09.2019 02:10

Batteries are used in a plc's processor to a. maintain data in nonvolatile memory when line power is removed from the processor. b. maintain data in v...

Engineering, 14.09.2019 02:10

Acomplex cmos fabrication process requires 25 masks a. what fraction of the dice must be good (i. e. what yield must be obtained) during each mask ste...

Engineering, 14.09.2019 02:10

Draw and label a typical true stress-strain curve for a ductile material....

Engineering, 14.09.2019 02:10

Draw and label a typical engineering stress-strain curve for a brittle material....

Engineering, 14.09.2019 02:10

Determine the length l of each of the slender rods of mass m/2 which must be centrally attached to the faces of the thin homogeneous disk of mass m in...

Engineering, 14.09.2019 02:10

Afour-stroke cycle engine delivers a torque of 437 ft-lb at the flywheel (output shaft) when the engine speed is 2100 rpm while using 514 hp of fuel e...

Engineering, 14.09.2019 02:10

It takes a man 12.5 hours to complete a 500-mile trip in his automobile, during which 18 gallons of gasoline are consumed. during this trip, the avera...

Engineering, 14.09.2019 02:10

For a motor purchased for a tank project, it claims that at 12v it produces 6000 rpm. this motor is attached to a 50: 1 gear reduction gearbox. the ou...

Engineering, 14.09.2019 02:10

Which of the two materials (brittle vs. ductile) usually obtains the largest modulus of toughness and why?...

Engineering, 14.09.2019 02:10

Afour-cylinder chrysler si engine has the following characteristics: 2.2l displacement, 87.5 mm bore, 92 mm stroke, 8.9 compression ratio, and a maxi...

Physics, 14.09.2019 02:10

Abead with a mass of 0.050 g and a charge of 20 nc is free to slide on a vertical rod. at the base of the rod is a fixed 20 nc charge. in equilibrium,...

Engineering, 14.09.2019 02:10

Which of the two materials (brittle vs. ductile) usually obtains the highest ultimate strength and why?...

Physics, 14.09.2019 02:10

Asmall bead with a positive charge q is free to slide on a horizontal wire of length 4.5 cm . at the left end of the wire is a fixed charge q, and at...

Physics, 14.09.2019 02:10

A1500kg space probe is moving at constant velocity of 4200m/sec. in a course change maneuver the rocket engines fire for 5 minutes increasing the prob...

Physics, 14.09.2019 02:10

Aconvex lens of focal length 35 cm produces a magnified image 2.5 times the size of the object. what is the object distance if the image (formed) is r...

Engineering, 14.09.2019 02:10

For reactor calculations it is very important to know the atom densities of all the isotopes in the reactor since each isotope reacts differently with...

More questions: Mathematics Another questions