subject
History, 23.10.2019 16:00 gmaxgaming88

Who was chosen to write the declaration of independence?
a. john hancock
b. thomas paine
c. patrick henry
d. thomas jefferson

ansver
Answers: 2
Show answers

Another question on History

question
History, 22.06.2019 01:30
Which 19th century technological advancement would best allow farmers along the mississippi river in iowa to quickly transport their crops to buyers in louisiana?
Answers: 1
Answer
question
History, 22.06.2019 08:00
What evidence is there in this document that the policy was a good idea?
Answers: 1
Answer
question
History, 22.06.2019 08:30
What is the effect of king mentioning his nobel prizes ?
Answers: 1
Answer
question
History, 22.06.2019 10:30
The supreme court case mcculloch versus maryland endured that
Answers: 1
Answer
You know the right answer?
Who was chosen to write the declaration of independence?
a. john hancock
b. thomas pa...
Questions
question
Engineering, 14.09.2019 02:10
The condition of irrotationality for a two-dimensional flow is satisfied when rotation w everywhere is (less than — equal to — more than) zero....
question
Engineering, 14.09.2019 02:10
The flow of a real fluid has (more —less - same ) complexity of an ideal fluid, owing to the phenomena caused by the existence of (viscosity-pressure...
question
Engineering, 14.09.2019 02:10
In laminar now, fluid particles are constrained to motion in (parallel —perpendicular opposite) paths by the action of (temperature- viscosity —pressu...
question
Engineering, 14.09.2019 02:10
Which of the following is not a function of a plc programming device? a. to enter the user program b. to monitor the user program c. to execute the u...
question
Engineering, 14.09.2019 02:10
Acertain measurement is performed 50 times. the arithmetic mean reading is 7.163 ft., and the standard deviation is 0.01 ft. how many readings fall wi...
question
Engineering, 14.09.2019 02:10
Apolyimide photoresist requires 90 mj/cm^2 per micron of thickness to be developed properly. if a lamp provides 900 w/m, how long does it take to expo...
question
Engineering, 14.09.2019 02:10
Determine ixx for the cylinder with a concentarted circular hole. the mass of body is m...
question
Engineering, 14.09.2019 02:10
Two 14.5° pressure angle, mating, 5-pitch gears have 30 and 110 teeth. in practice, the gears are mounted at a center distance 0.7 inches greater than...
question
Engineering, 14.09.2019 02:10
The center distance of two spur gears that have 20° pressure angle and full-depth with diametral pitch of 8 teeth/in, is increased by 0.05 in over the...
question
Engineering, 14.09.2019 02:10
Two meshing 24-pitch, 25° pressure angle gears have n1-24 and n2 60 teeth. the in use center distance of the two gears is 0.16 inches larger than the...
question
Engineering, 14.09.2019 02:10
Batteries are used in a plc's processor to a. maintain data in nonvolatile memory when line power is removed from the processor. b. maintain data in v...
question
Engineering, 14.09.2019 02:10
Acomplex cmos fabrication process requires 25 masks a. what fraction of the dice must be good (i. e. what yield must be obtained) during each mask ste...
question
Engineering, 14.09.2019 02:10
Draw and label a typical true stress-strain curve for a ductile material....
question
Engineering, 14.09.2019 02:10
Draw and label a typical engineering stress-strain curve for a brittle material....
question
Engineering, 14.09.2019 02:10
Determine the length l of each of the slender rods of mass m/2 which must be centrally attached to the faces of the thin homogeneous disk of mass m in...
question
Engineering, 14.09.2019 02:10
Afour-stroke cycle engine delivers a torque of 437 ft-lb at the flywheel (output shaft) when the engine speed is 2100 rpm while using 514 hp of fuel e...
question
Engineering, 14.09.2019 02:10
It takes a man 12.5 hours to complete a 500-mile trip in his automobile, during which 18 gallons of gasoline are consumed. during this trip, the avera...
question
Engineering, 14.09.2019 02:10
For a motor purchased for a tank project, it claims that at 12v it produces 6000 rpm. this motor is attached to a 50: 1 gear reduction gearbox. the ou...
question
Engineering, 14.09.2019 02:10
Which of the two materials (brittle vs. ductile) usually obtains the largest modulus of toughness and why?...
question
Engineering, 14.09.2019 02:10
Afour-cylinder chrysler si engine has the following characteristics: 2.2l displacement, 87.5 mm bore, 92 mm stroke, 8.9 compression ratio, and a maxi...
More questions: History Another questions
Questions on the website: 13722367
See results (0)