English, 02.10.2019 04:00 dylancasebere

Identify the fused sentence.
a.
i was thrilled to find my keys, they had been lost since yesterday.
b.
i was thrilled to find my keys; they had been lost since yesterday.
c.
i was thrilled to find my keys they had been lost since yesterday.
d.
i was thrilled to find my keys. they had been lost since yesterday.

Answers: 1

Show answers

Another question on English

English, 21.06.2019 16:40

Use the two columns to sort the characters into the appropriate households to indicate which side of the feud each character is on romeo capulet montague benvolio tybalt mercutio the nurse juliet previous activity

Answers: 1

Answer

English, 22.06.2019 05:40

Which character shows external character development in the crucible

Answers: 1

Answer

English, 22.06.2019 08:30

By comparing part i and part ii of "polar opposites" what can you tell that the poet means by polar opposites poet

Answers: 1

Answer

English, 22.06.2019 08:30

Tony ran down the stairs. the prepositional phrase is

Answers: 1

Answer

You know the right answer?

Identify the fused sentence.
a.
i was thrilled to find my keys, they had been lost since...

Questions

Engineering, 26.07.2019 19:10

Arectangular block having dimensions 20 cm x 30 cm x 40 cm is subjected to a hydrostatic stress of -50 kpa (i. e. under compression). calculate the ch...

Engineering, 26.07.2019 19:10

Astainless steel (sae 301) wire is stretched between rigid supports so that a stress of 40 mpa is induced in the wire at a temperature of 20°c. what w...

Engineering, 26.07.2019 19:10

During sheet metal bending, springback is the increase in bend angle and the increase in bend radius. the increase in bend angle and the decrease in b...

Engineering, 26.07.2019 19:10

Avehicle of 1 200 kg is moving at a speed of 40 km/h on an incline of 1 in 50. the total constant rolling and wind resistance is 600 n. the efficiency...

Engineering, 26.07.2019 19:10

Using a 2-d mohr's circle, prove the relationship between the elastic modulus e, shear modulus g and poisson ratio is given by the equation e=2g(1+v )...

Engineering, 26.07.2019 19:10

Consider a pb-40 %sn alloy. determine the composition of the first solid to form during solidification. (i) (ii) the amounts and composition of each p...

Engineering, 26.07.2019 19:10

Why might peck drilling be used instead of standard drilling with a 0.25" diameter hole which is 3 inches deep on a aluminum part? a. to save time b....

Engineering, 26.07.2019 19:10

Amulti-plate clutch connects two in-line shafts, through 4 plates on the driving and 3 plates driven shaft. the plates have inner and outer diameters...

Engineering, 26.07.2019 19:10

Ametal sphere of 6- in internal diameter is weighed on a beam balance when it is empty (all gas evacuated be- fore weighing). it is then filled with a...

Engineering, 26.07.2019 19:10

Afour-cylinder, two-stroke 2.4-l diesel engine that operates on an ideal diesel cycle has a compression ratio of 22 and a cutoff ratio of 1.8. air is...

Engineering, 26.07.2019 19:10

Aring of sae 301 stainless steel is to be placed on a shaft having a temperature of 20°c and a diam- eter of 55.200 mm. the inside diameter of the rin...

Engineering, 26.07.2019 19:10

Determine the change in the entropy of air, in kj/kg-k, as it undergoes a change of state from 100 kpa and 20°c to 600 kpa and 300°c using the equatio...

Engineering, 26.07.2019 19:10

What is one of the biggest drawback to using a conventional 3d printer for manufacturing parts? a. it can only print in metal materials such as alumi...

Engineering, 26.07.2019 19:10

During casting and solidification, shrinkage includes: a)-liquid contraction during cooling prior to solidification. b)-contraction during the phase...

Engineering, 26.07.2019 19:10

Afiber-reinforced polymer composite consists of a matrix of vinyl ester and reinforcing short fibers of e-glass. the volume fraction of e-glass fibres...

Engineering, 26.07.2019 19:10

Acentrifugal pump running at 500 rpm and at its maximum efficiency it is delivering a head of 30 m at a flow rate of 60 litres per minute if the rpm i...

Engineering, 26.07.2019 19:10

Ashaft of circular cross section (diameter = 3 in) is subjected to a bending moment of 3200 lb- ft. determine the bending stress at the surface of the...

Engineering, 26.07.2019 19:10

The nozzles of a simple impulse steam turbine are inclined at an angle of 20° to the direction of the path of the moving blades and steam leaves the n...

Engineering, 26.07.2019 19:10

Awinding drum raises a cage of mass 800 kg though a height 100 m. the winding drum has a mass of 200 kg and an effective radius of 0.5 m and a radius...

Engineering, 26.07.2019 19:10

Steam at 120°c flows in an insulated 1% carbon steel pipe. the pipe inner radius is 10 cm and the outer radius is 11 cm. this is covered with a 3 cm t...

More questions: English Another questions