subject
Engineering, 21.05.2020 04:00 kimberlylove387

1. Where are the output windings on an AC generator?
a. Stator
b. Rotor with commutator
c. Rotor with slip rings
d. None of the above

2. A generator rated for 30 KVA and power factor 0.8 has a maximum power output of:
a. 30 KW
b. 24 KW
c. 48 KW
d. None of the above

3. The voltage of an AC generator:
a. Rises to max in one direction and remains constant
b. Rises to max in one direction, falls to zero and rises in the same direction
c. Rises to max in one direction then fall to zero then rises to max in the opposite direction
d. None of the above

4. Power factor of a generator is:
a. Tan Ó¨
b. Cos Ó¨
c. Sin Ó¨
d. None

5. A generator supplied 150 V AC phase and load is 10 Ohms per phase. What is the phase current?
a. 25.5 A
b. 15 A
c. 1.5 A
d. None of the above

6. An AC generator’s frequency will:
a. Be proportional to the RPM at which it is driven
b. Always be constant regardless of the generators drive speed
c. Vary with changes in field strength.
d. None of the above

7. The sum of the instantaneous EMF’s in a three phase system is:
a. Three times the phase voltage
b. Zero
c. Equal to the line voltage
d. None of the above

8. The line voltage from a generator with a delta type connection will be:
a. Lower than the phase voltage
b. The same as the phase voltage
c. Higher than the phase voltage
d. None of the above
9. Permanent magnets in an AC generator are:
a. To provide initial excitation
b. To rectify the current
c. To control the frequency
d. None of the above

10. In delta-connected generator:
a. Line voltage = root 3 ties phase voltage, line current = phase current
b. Line voltage = phase voltage, line current = root 3 times phase current
c. Line voltage = phase voltage, line current =phase current divided by root 3
d. None of the above

ansver
Answers: 1

Another question on Engineering

question
Engineering, 03.07.2019 14:10
The y form of iron is known as: a) ferrite b) cementite c) perlite d) austenite
Answers: 3
question
Engineering, 04.07.2019 18:10
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
question
Engineering, 04.07.2019 18:10
Consider a large isothermal enclosure that is maintained at a uniform temperature of 2000 k. calculate the emissive power of the radiation that emerges from a small aperture on the enclosure surface. what is the wavelength ? , below which 10% of the emission is concentrated? what is the wavelength ? 2 above which 10% of the emission is concentrated? determine the wavelength at which maximum spectral emissive power occurs. what is the irradiation incident on a small object placed inside the enclosure?
Answers: 2
question
Engineering, 04.07.2019 18:10
Draw the engineering stress-strain curve for (a) bcc; (b) fcc metals and mark important points.
Answers: 1
You know the right answer?
1. Where are the output windings on an AC generator?
a. Stator
b. Rotor with commutator<...
Questions
question
Mathematics, 14.04.2020 19:33
question
Mathematics, 14.04.2020 19:34
Questions on the website: 13722367