Arts, 03.11.2020 20:10 unknown1246

CC rp or fnaf only (FANS only) btw

Answers: 3

Show answers

Another question on Arts

Arts, 23.06.2019 15:30

The proper way to fly the flag of us

Answers: 1

Answer

Arts, 24.06.2019 07:20

Look at this madonna by parmigianino. ·describe its unique features. ·discuss the effect parmigianino is able to produce in this painting

Answers: 1

Answer

Arts, 24.06.2019 13:30

Answer the following question in 3-4 sentences. what is the above image of? why was it created

Answers: 3

Answer

Arts, 25.06.2019 02:00

Any surface such as a table, cutting board, or a piece of equipment that comes in contact with food is considered what

Answers: 2

Answer

You know the right answer?

CC rp or fnaf only (FANS only) btw...

Questions

Mathematics, 14.09.2019 01:30

The tallest living man at one time had a height of 230 cm. the shortest living man at that time had a height of 91.3 cm. heights of men at that time h...

Mathematics, 14.09.2019 01:30

An equation one solution. alwa sometimes never...

English, 14.09.2019 01:30

Select the correct answer. which of the following is a defining characteristic of an ethical appeal?...

Engineering, 14.09.2019 01:30

By = 4.8 kn ay = 6,.0 kn there is the wrong perpendicular distance in the summation ofmoments about a formula for by....

Engineering, 14.09.2019 01:30

W= 600 draw the fbd and determine the reactions at the support(s)....

Engineering, 14.09.2019 01:30

The magnitude of the concentrated load is equal to the total load or the area under the curve. f = 18.0 kn the line of action of the concentrated load...

Engineering, 14.09.2019 01:30

Determine all the forces axerted on member ai when a clockwisecouple of magnitude 180 ft. lb is applied to the frame (a) at pointd, (b) at...

Engineering, 14.09.2019 01:30

At the instant shown, rod a b lias an angular velocity omegaab = 3 rad/s and an angular acceleration alphaab = 5 rad/s2. determine the angular velocit...

Engineering, 14.09.2019 01:30

At the instant shown, the velocity of collar a is 0.4m/s to the right and the velocity of collar b is 1m/s to the left. determine (a) the angular velo...

Engineering, 14.09.2019 02:10

The condition of irrotationality for a two-dimensional flow is satisfied when rotation w everywhere is (less than — equal to — more than) zero....

Engineering, 14.09.2019 02:10

The flow of a real fluid has (more —less - same ) complexity of an ideal fluid, owing to the phenomena caused by the existence of (viscosity-pressure...

Engineering, 14.09.2019 02:10

In laminar now, fluid particles are constrained to motion in (parallel —perpendicular opposite) paths by the action of (temperature- viscosity —pressu...

Engineering, 14.09.2019 02:10

Which of the following is not a function of a plc programming device? a. to enter the user program b. to monitor the user program c. to execute the u...

Engineering, 14.09.2019 02:10

Acertain measurement is performed 50 times. the arithmetic mean reading is 7.163 ft., and the standard deviation is 0.01 ft. how many readings fall wi...

Engineering, 14.09.2019 02:10

Apolyimide photoresist requires 90 mj/cm^2 per micron of thickness to be developed properly. if a lamp provides 900 w/m, how long does it take to expo...

Engineering, 14.09.2019 02:10

Determine ixx for the cylinder with a concentarted circular hole. the mass of body is m...

Engineering, 14.09.2019 02:10

Two 14.5° pressure angle, mating, 5-pitch gears have 30 and 110 teeth. in practice, the gears are mounted at a center distance 0.7 inches greater than...

Engineering, 14.09.2019 02:10

The center distance of two spur gears that have 20° pressure angle and full-depth with diametral pitch of 8 teeth/in, is increased by 0.05 in over the...

Engineering, 14.09.2019 02:10

Two meshing 24-pitch, 25° pressure angle gears have n1-24 and n2 60 teeth. the in use center distance of the two gears is 0.16 inches larger than the...

Engineering, 14.09.2019 02:10

Batteries are used in a plc's processor to a. maintain data in nonvolatile memory when line power is removed from the processor. b. maintain data in v...