subject
Physics, 12.01.2022 14:00 smonahan2023

Runner A is initially 2.0 mi west of a flagpole and is running with a constant velocity of 8.0 mi/h due east. Runner B is initially 9.0 mi east of the flagpole and is running with a constant velocity of 4.0 mi/h due west. How far are the runners from the flagpole when they meet?

ansver
Answers: 2

Another question on Physics

question
Physics, 21.06.2019 20:30
Asmall metal bar, whose initial temperature was 10° c, is dropped into a large container of boiling water. how long will it take the bar to reach 70° c if it is known that its temperature increases 2° during the first second? (the boiling temperature for water is 100° c. round your answer to one decimal place.) sec how long will it take the bar to reach 98° c? (round your answer to one decimal place.)
Answers: 2
question
Physics, 22.06.2019 00:00
Name three different units of energy used to measure heat and describe what type of situations each is usually used.
Answers: 2
question
Physics, 22.06.2019 00:30
Part f - example: finding two forces (part i) two dimensional dynamics often involves solving for two unknown quantities in two separate equations describing the total force. the block in (figure 1) has a mass m=10kg and is being pulled by a force f on a table with coefficient of static friction îľs=0.3. four forces act on it: the applied force f (directed î¸=30â above the horizontal). the force of gravity fg=mg (directly down, where g=9.8m/s2). the normal force n (directly up). the force of static friction fs (directly left, opposing any potential motion). if we want to find the size of the force necessary to just barely overcome static friction (in which case fs=îľsn), we use the condition that the sum of the forces in both directions must be 0. using some basic trigonometry, we can write this condition out for the forces in both the horizontal and vertical directions, respectively, as: fcosî¸â’îľsn=0 fsinî¸+nâ’mg=0 in order to find the magnitude of force f, we have to solve a system of two equations with both f and the normal force n unknown. use the methods we have learned to find an expression for f in terms of m, g, î¸, and îľs (no n).
Answers: 2
question
Physics, 22.06.2019 03:00
An internally reversible refrigerator has a modified coefficient of performance accounting for realistic heat transfer processes of where qin is the refrigerator cooling rate, qout is the heat rejection rate, and is the power input. show that copm can be expressed in terms of the reservoir temperatures tc and th, the cold and hot thermal resistances rt,c and rt,h, and qin, as where rtot rt,c rt,h. also, show that the power input may be expressed as 1.39 a household refrigerator operates with cold- and hot-temperature reservoirs of tc 5 c and th 25 c, respectively. when new, the cold and hot side resistances are rc,n 0.05 k/w and rh,n 0.04 k/w, respectively. over time, dust accumulates on the refrigerator’s condenser coil, which is located behind the refrigerator, increasing the hot side resistance to rh,d 0.1 k/w. it is desired to have a refrigerator cooling rate of qin 750 w. using the results of problem 1.38, determine the modified coefficient of performance and the required power input w under (a) clean and (b) dusty coil conditions. internally reversible refrigerator qout qin w high-temperature reservoir low-temperature reservoir th th,i tc,i tc high-temperature side resistance low-temperature side resistance w qin th tc qinrtot tc qinrtot copm tc qinrtot th tc
Answers: 2
You know the right answer?
Runner A is initially 2.0 mi west of a flagpole and is running with a constant velocity of 8.0 mi/h...
Questions
question
Mathematics, 07.12.2021 08:00
question
Mathematics, 07.12.2021 08:00
question
English, 07.12.2021 08:00
question
Mathematics, 07.12.2021 08:00
Questions on the website: 13722361