Physics, 13.09.2021 19:10 heavenmckissack21
Jeff is part of a trekking team. As he climbs a hill, he drops his water bottle, which has a mass of 0.25 kilograms.
The bottle slides down the hill and is moving at a velocity of 14 meters/second the instant it hits the ground. The vertical height from where Jeff dropped the bottle is
meters. Ignore friction, and use , PE = m Ć g Ć h, and g = 9.8 m/s2.
Answers: 2
Physics, 21.06.2019 23:30
Jessie ran 5000 meters from the cops and an average speed of 6 meters / second before he got caught . how long did he run?
Answers: 1
Physics, 22.06.2019 15:10
Suppose that f : rn ā rm and that a ā k, where k is a connected subset of rn . suppose further that for each x ā k there exists a Ī“x > 0 such that f(x) = f(y) for all y ā bĪ“x (x). prove that f is constant on k; that is, f(x) = f(a) for all x ā k
Answers: 1
Physics, 22.06.2019 18:50
Avertical clean glass piezometer tube has an inside diameter of d = 1 mm and is used to measure pressure in a horizontal pipe carrying water as shown. due to pressure in the pipe, the water at 20ļ°c rises into the tube to a height h. if the water pressure in the pipe is p = 500 pa gauge, estimate the height h: (a) without considering surface tension (b) with surface tension (capillary) effects. the contact angle ļ± can be assumed at 30 deg
Answers: 2
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (Īµ)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
Jeff is part of a trekking team. As he climbs a hill, he drops his water bottle, which has a mass of...
Mathematics, 26.07.2019 16:30
Social Studies, 26.07.2019 16:30
Mathematics, 26.07.2019 16:30
History, 26.07.2019 16:30
Social Studies, 26.07.2019 16:30
Advanced Placement (AP), 26.07.2019 16:30
Chemistry, 26.07.2019 16:30
Advanced Placement (AP), 26.07.2019 16:30
Social Studies, 26.07.2019 16:30
Physics, 26.07.2019 16:30
History, 26.07.2019 16:30
Biology, 26.07.2019 16:30