Physics, 22.09.2019 03:30 violetagamez2

Which statement about a chemical reaction is true?
it occurs only at low temperatures.
it occurs only at high temperatures.
it occurs whenever a physical change takes place.
it occurs whenever a chemical change takes place.

Answers: 1

Show answers

Another question on Physics

Physics, 22.06.2019 19:30

The nuclear potential that binds protons and neutrons in the nucleus of an atom is often approximated by a square well. imagine a proton conned in an innite square well of length 105 nm, a typical nuclear diameter. calculate the wavelength and energy associated with the photon that is emitted when the proton undergoes a transition from the rst excited state (n 2) to the ground state (n 1). in what region of the electromagnetic spectrum does this wavelength belong?

Answers: 1

Answer

Physics, 22.06.2019 19:40

Which of the following is a characteristic shared by both electron and light microscopes? a. they both employ the use of objective lenses. b. both microscopes require an internal camera to visualize the specimen. c. both microscopes have a resolving power of 0.01 nm. d. they both utilize white light to magnify the specimen.

Answers: 2

Answer

Physics, 23.06.2019 02:00

Two technicians are discussing a starter that clicks repeatedly when the key is turned to the crank position. technician a says the solenoid hold-in winding is open. technician b says the solenoid pull-in winding is open. who is correct?

Answers: 2

Answer

Physics, 23.06.2019 08:30

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

Answer

You know the right answer?

Which statement about a chemical reaction is true?
it occurs only at low temperatures.
...

Questions