Answers: 1
Physics, 22.06.2019 17:40
The first-order reaction a→2b+c has rate constant 0.538 s−1. if the initial concentration of a is 0.867 mol l−1, what is the half-life of the reaction in seconds? remember to use correct significant figures in your answer (round your answer to the nearest hundredth). do not include units in your response.
Answers: 3
Physics, 23.06.2019 08:00
Stephanie lives in california, and her cousin thomas lives in france. which coordinate system would be most useful if the two wanted to observe the same meteor shower and discuss their observations over online chat as they're making them? a. horizontal b. equatorial c. azimuth-altitude d. celestial or azimuth-altitude
Answers: 1
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
Physics, 23.06.2019 11:30
Match the lithification processes. 1. contact pressure causing grains to "grow" together 2. increase in density due to weight of overburden 3. precipitation of bonding agents between grains a. recrystallization b. cementation c. compaction
Answers: 1
What is the maximum powr of a module in Watts to the nearest whole Watt?...
Mathematics, 17.12.2019 22:31
Geography, 17.12.2019 22:31
Mathematics, 17.12.2019 22:31
History, 17.12.2019 22:31
Chemistry, 17.12.2019 22:31