Physics, 12.11.2020 02:10 dicewillis

3. What will happen when a light bulb is removed from the circuit below? A .The remaining light bulbs go out.
B. The remaining light bulbs witdim
C. The brightness of the remaining light bulbs will not change
D. The remaining light but will brighten

3. What will happen when a light bulb is removed from the circuit below?

A .The remaining light b

Answers: 1

Show answers

Another question on Physics

Physics, 22.06.2019 06:30

Alead ball is dropped into a lake from a diving board 5m above the water . it hits the water with a certain velocity and then sink with constant velocity in bottom . it reaches the bottom 5 second after it is dropped if g= 10m/s2 . find depth of the lake and average velocity of the ball ?

Answers: 1

Answer

Physics, 22.06.2019 23:20

Acharge q experiences no net force at a particular point in space. which of the following situations described below must always be true? -there are no other charges nearby. -if there are other charges nearby, they must all have the same sign as q. -if there are other charges nearby, they must all have the opposite sign of q. -if there are other charges nearby, the total positive charge must equal the total negative charge. -none of the above

Answers: 2

Answer

Physics, 23.06.2019 07:30

Neurons are components of the nervous system of the body that transmit signals as electrical impulses travel along their length. these impulses propagate when charge suddenly rushes into and then out of a part of the neutron called an axon. measurements have shown that, during the inflow part of this cycle approximately 5.6x10^11 na per meter, each with a charge of e enter the axon. how many coulombs of charge enter a 1.10 cm length of axon during this process

Answers: 2

Answer

Physics, 23.06.2019 08:30

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

Answer

You know the right answer?

3. What will happen when a light bulb is removed from the circuit below? A .The remaining light bul...

Questions