Physics, 02.11.2020 16:50 patriciaceaser2980

What is the net loss of hydrogen for each full cycle of the proton-proton chain? Explain.

Answers: 1

Show answers

Another question on Physics

Physics, 22.06.2019 08:30

Researchers determine that the biodiversity in a woodland region is declining. they identify two major threats to the region's biodiversity, a method to address each threat, and the expected outcome of each method. this information is shown in the table. a) reforestation would not benefit many species because most forest species live on the ground. b) reforestation would take the longest time to be effective because trees take several years to grow. c) biological augmentation would benefit only a few species because is is typically not very effective. d) biological augmentation would take less time to ve effective because it targets the majority of prey species.

Answers: 3

Answer

Physics, 22.06.2019 13:50

9.98 kg of r-134a at 300 kpa fills a rigid container whose volume is 14 l. determine the temperature and total enthalpy in the container. the container is now heated until the pressure is 600 kpa. determine the temperature and total enthalpy when the heating is completed. use data from the steam tables.

Answers: 1

Answer

Physics, 22.06.2019 22:30

An alarm clock has a current of 4.5 amps and a resistance of 3.2 ohms. what is the voltage in the circuit? a.1.4 volts b.0.71 volts c.14 volts d.46 volts

Answers: 2

Answer

Physics, 23.06.2019 08:30

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

Answer

You know the right answer?

What is the net loss of hydrogen for each full cycle of the proton-proton chain? Explain....

Questions