DEPIC Curriculum
Tools
Save for Later
Tu
Conflicting Viewpoints: Physics Pra...
DEPIC Curriculum
Tools
Save for Later
Tu
Conflicting Viewpoints: Physics Practice
1
Which of the following constraints would most likely limit the effectiveness of the design of Student 1?
Š Š.
A limited amount of horizontal space
OB
A ramp that is not steep enough
C.
A time limit of eight hours
Two students must build a device or structure that can lift a
stalled, 1,000-kg tractor up to a mobile 5-meter-high
platform. The only motor available to them can apply a
maximum of 2,000 N, which is approximately enough to lift
a 200-kg weight. The students have varying opinions
about the best method to raise the tractor onto the
platform
Student 1
The best way to raise the tractor onto the platform is to
build a ramp and use the motor to pull the tractor up onto
the platform. The motor will be positioned at the top of the
ramp and connected to the tractor with a cable. The
platform will need to be fixed in place as the tractor will be
pulled up the ramp and straight onto the platform, as
shown in the following diagram (diagram not to scale).
OD
A low-efficiency motor
Reset
Next Question
Motor
o
Sign out
Answers: 3
Physics, 22.06.2019 00:30
Ablock of steel has a density of 0.29lbs per cubic inch. if the block has dimensions of 1 inch by 1 inch by 3 inches, what is its weight? a. 0.29lbs b. 0.58lbs c. 0.87lbs d. 1lbs
Answers: 1
Physics, 22.06.2019 01:10
If vx = 7.00 units and vy = -7.60 units, determine the magnitude of vā . determine the direction of vā .
Answers: 2
Physics, 22.06.2019 06:30
5submission this assignment is worth 20 points total. you are required to submit the following by next lab: 1. (3 points) determine the equation for the output angular velocity Ļ2 = ĪøĖ 2 as a function of Īø1, Ļ1 = ĪøĖ 1 and Ī±. you must show all your work to receive credit. 2. (2 points) use the result of problem#1 to plot Ļ2 over 0 ā¤ Īø1 ā¤ 360deg with Ļ1 = 360deg/sec. do this for Ī± = {10,30}deg. show the results on the same plot and properly label the axes, title, legend. for this you can use matlab or ms excel. 3. (3 points) determine the equation for the output angular acceleration ĻĖ 2 and create a plot similar to the one in problem#2. 4. (10 points) submit plots of the results (Ļ2 and ĻĖ 2) obtained from creo/mechanism and compare them to results of problem#2 and problem#3. note that you should do these comparisons for the two cases with Ī± = {10,30}deg. 5. (2 points) provide a brief explanation of the results. did they match? what are the implications as misalignment angle increases?
Answers: 3
Physics, 22.06.2019 07:00
If a tank filled with water contains a block and the height of the water above point a within the block is 0.8 meter, what is the pressure at point a?
Answers: 2
English, 11.03.2021 04:10
Mathematics, 11.03.2021 04:10
Arts, 11.03.2021 04:10
History, 11.03.2021 04:10
Mathematics, 11.03.2021 04:10
Mathematics, 11.03.2021 04:10
History, 11.03.2021 04:10
Mathematics, 11.03.2021 04:10
Mathematics, 11.03.2021 04:10
Mathematics, 11.03.2021 04:10