Physics, 27.05.2020 05:58 princessgabbee8452

The internal loadings at a section of the beam are shown. Determine the in-plane principal stresses at point A. Also compute the maximum in-plane shear stress at this point.

The internal loadings at a section of the beam are shown. Determine the in-plane principal stresses

Answers: 1

Show answers

Answers

Answer from: avision42

=> In-plane principal stresses at point A = 14.18 MPa and -8.02 MPa.

=> maximum in-plane shear stress= 11.1 MPa.

Explanation:

Okay, we are given the following Important parameters or information or data which is going to assist us in order to solve this question effectively and efficiently.

Jy = 500 Nm, Jb = 10 KNm, wy = 60 KN, wx = -80 KN.

Thus, I(bb) = 10/12 × 100 × (200 + 2 × 20)^3 - 1/2 (100 - 20) × 200^3.

l(bb) = 6.19 × 107 mm^4.

l(yy) = 1/12 × 20 × 240^3 × 2 + 1/2 × 200 × 20^3.

l(yy) = 4.62 × 10^7 mm^4.

Thus, the bending stress due to Jy = Jy × y / l(bb)

=> 500 × 10^ 3 × 0 /l(yy) = 0 MPa.

The bending stress due to Jb;

=> 500 × 10^ 6 ×( 200/2)/ 6.19 × 10^7 = 16.16 MPa.

The bending stress due to wx = wx/A= -80/800 = 10 MPa.

Transverse share stress = 60 × 10^3 × 220000/ 6.19 × 10^ 7 × 20 = 10.66 MPa.

Principal stresses= T1 - T3/ 2 +/- ( T1 - T3/)^2 + c^2.

=> 16.16 - 10/2 +/- (16.16 -10)^2 + 10.66^2.

=> 3.08 +/- 11.1.

=> = 14.18 MPa and -8.02 MPa.

=> maximum in-plane shear stress = ( T1 - T3/)^2 + c^2 = 16.16 -10)^2 + 10.66^2.

= 11.1 MPa.

Answer from: Quest

nec chapter 5 contains

c. information on special occupancy areas

nec chapter 6 covers

a. special equipment

which of the following rules contain the words shall or shall not and must be adhered to?

b. mandatory rules

which of the following rules identify actions that are allowed but not required and typically cover options or alternative methods?

c. optional rules

which of the following serves as the introduction to the nec and provides an overview of the book?

a. nec article 90

organizations that test products for safety are

c. nrtls

the nec is published by the

a national fire protection association

the nec is divided into

b. 9 chapters

the nec provides informative annexes for

c. informational materials and examples

two terms from nec article 100 that trainees should become familiar with are

b. labeled and listed

explanation:

Answer from: Quest

hujjujddf

Another question on Physics

Physics, 22.06.2019 05:00

At time t=0, a particle is located at the point (3,6,9). it travels in a straight line to the point (5,2,7), has speed 8 at (3,6,9) and constant acceleration 2i−4j−2k. find an equation for the position vector of the particle.

Answers: 2

Answer

Physics, 22.06.2019 14:20

4r-134a enters the condenser of a residential heat pump at 800 kpa and 50°c at a rate of 0.022 kg/s and leaves at 750 kpa subcooled by 3°c. the refrigerant enters the compressor at 200 kpa superheated by 4°c determine (a) the isentropic efficiency of the compressor, (b) the rate of heat supplied to the heated room, and (c) the cop of the heat pump. also, determine (d) the cop and rate of heat supplied to the heated room if this heat pump operated on the ideal vapor-compression cycle between the pressure limits of 200 and 800 kpa. (0.757, 4.37 kw, 5.12, 6.18, 3.91 kw)

Answers: 3

Answer

Physics, 22.06.2019 16:30

The air in an automobile tire with a volume of 2.60 ft3 is at 70°f and 21 psig. determine the amount of air that must be added to raise the pressure to the recommended value of 30 psig. assume the atmospheric pressure to be 14.6 psia and the temperature and the volume to remain constant. the gas constant of air is ru = 53.34ft⋅lbflbm⋅r(1 psia144 lbf/ft2) = 0.3704 psia⋅ft3lbm⋅r the amount of air that must be added to raise the pressure is lbm

Answers: 3

Answer

Physics, 23.06.2019 02:30

Failure to accomplish erikson’s psychosocial task of late adulthood leads to despair. a. true b. false

Answers: 1

Answer

You know the right answer?

The internal loadings at a section of the beam are shown. Determine the in-plane principal stresses...

Questions