Physics, 21.04.2020 15:52 Dweath50

The 1.18-kg uniform slender bar rotates freely about a horizontal axis through O. The system is released from rest when it is in the horizontal position θ = 0 where the spring is unstretched. If the bar is observed to momentarily stop in the position θ = 46°, determine the spring constant k. For your computed value of k, what is magnitude of the angular velocity of the bar when θ = 30°.

Answers: 3

Show answers

Answers

Answer from: hartmaaj95

k = 11,564 N / m, w = 6.06 rad / s

Explanation:

In this exercise we have a horizontal bar and a vertical spring not stretched, the bar is released, which due to the force of gravity begins to descend, in the position of Tea = 46º it is in equilibrium;

let's apply the equilibrium condition at this point

Axis y

W_{y} - Fr = 0

Fr = k y

let's use trigonometry for the weight, we assume that the angle is measured with respect to the horizontal

sin 46 = $W_{y}$ / W

W_{y} = W sin 46

we substitute

mg sin 46 = k y

k = mg / y sin 46

If the length of the bar is L

sin 46 = y / L

y = L sin46

we substitute

k = mg / L sin 46 sin 46

k = mg / L

for an explicit calculation the length of the bar must be known, for example L = 1 m

k = 1.18 9.8 / 1

k = 11,564 N / m

With this value we look for the angular velocity for the point tea = 30º

let's use the conservation of mechanical energy

starting point, higher

Em₀ = U = mgy

end point. Point at 30º

$Em_{f}$ = K -Ke = ½ I w² - ½ k y²

em₀ = Em_{f}

mgy = ½ I w² - ½ k y²

w = √ (mgy + ½ ky²) 2 / I

the height by 30º

sin 30 = y / L

y = L sin 30

y = 0.5 m

the moment of inertia of a bar that rotates at one end is

I = ⅓ mL 2

I = ½ 1.18 12

I = 0.3933 kg m²

let's calculate

w = Ra (1.18 9.8 0.5 + ½ 11,564 0.5 2) 2 / 0.3933)

w = 6.06 rad / s

Answer from: Quest

Awoodchuck would chuck all the wood he could chuck if a woodchuck could chuck wood.

Answer from: Quest

Aform of energy that is reflected or emitted from objects in the form of electrical and magnetic waves that can travel through space. there are many forms of electromagnetic energy including gamma rays, x rays, ultraviolet radiation, visible light, infrared radiation, microwaves and radio waves.

Another question on Physics

Physics, 22.06.2019 08:30

Abike rider starts from rest and accelerates 28.0 meters down a slope in 5.00 seconds. what is her acceleration? select one: a. 3.21 m/sec2 b. 1.75 m/sec2 c. 9.80 m/sec2 d. 2.24 m/sec2

Answers: 3

Answer

Physics, 22.06.2019 17:20

Properties seen when one one substance changes to another are known as properties

Answers: 1

Answer

Physics, 23.06.2019 08:20

Give an example of how both short term and long term memory are involved. explain procedural, semantic ,and episodic memory and then how each is involved in this

Answers: 2

Answer

Physics, 23.06.2019 08:30

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

Answer

You know the right answer?

The 1.18-kg uniform slender bar rotates freely about a horizontal axis through O. The system is rele...

Questions