Physics, 31.03.2020 00:58 qhenley

A long, fine wire is wound into a coil with inductance 5 mH. The coil is connected across the terminals of a battery, and the current is measured a few seconds after the connection is made. The wire is unwound and wound again into a different coil with L = 10 mH. This second coil is connected across the same battery, and the current is measured in the same way. Compared with the current in the first coil, is the current in the second coil

Answers: 1

Show answers

Answers

Answer from: khalaflaf2684

Compared with the current in the first coil, the current in the second coil is unchanged.

Explanation:

All coils, inductors, chokes and transformers create a magnetic field around themselves consist of an Inductance in series with a Resistance forming an LR Series Circuit.

The steady state of current in the LR circuit is:

I= V/R (1 - e^-Rt/L)

Where I= current

R= Resistance

V= Voltage

Where R/L is the time constant.

For a conducting wire, it has a very small resistance. The time constant will be in microseconds. The current will be in a steady state after few second. The current is independent on the inductance and dependent on the resistance. The length of wire and the resistance here are the same. Therefore, the current remains unchanged.

Answer from: youtubeviewer109

The current in both circuit instances are equal (the current is unchanged).

Explanation:

Provided that a voltage V is the voltage of the battery(capacitor)

The Inductance of the first wound wire, L1 = 5 mH

The Inductance of the second wound wire, L2 = 10 mH

The wire and battery contribute to the resistance of the circuit and consequently, the circuit has a total resistance ,R.

V = I R + L dI/dt

where, I is the current in the circuit and t is the time.

dI/dt which is the change in current with respect to time diminishes after a few seconds, this is due to constant current flowing through the circuit after this time.

Therefore,

The factor dI/dt becomes 0.

The same applies for the second coil with inductance, 10mH

There is no change in the current flowing through the circuit. when the 10mH inductor was just attached in the circuit, a current, I still flows through the circuit.

Based on the explanation above, the current remains unchanged.

Answer from: Quest

ammonium chloride & tallow

Answer from: Quest

spectral lines lyman is one set

Another question on Physics

Physics, 22.06.2019 05:00

Awalk up the phase change graph worksheet

Answers: 3

Answer

Physics, 22.06.2019 14:50

Nitrogen (n2) undergoes an internally reversible process from 6 bar, 247°c during which pν1.2 = constant. the initial volume is 0.1 m3 and the work for the process is 121.14 kj. assuming ideal gas behavior, and neglecting kinetic and potential energy effects, determine heat transfer, in kj, and the entropy change, in kj/s. show the process on a t-s diagram.

Answers: 2

Answer

Physics, 22.06.2019 23:00

Acommon technique in analysis of scientific data is normalization. the purpose of normalizing data is to eliminate irrelevant constants that can obscure the salient features of the data. the goal of this experiment is to test the hypothesis that the flux of light decreases as the square of the distance from the source. in this case, the absolute value of the voltage measured by the photometer is irrelevant; only the relative value conveys useful information. suppose that in part 2.2.2 of the experiment, students obtain a signal value of 162 mv at a distance of 4 cm and a value of 86 mv at a distance of 5.7 cm. normalize the students' data to the value obtained at 4 cm. (divide the signal value by 162.) then calculate the theoretically expected (normalized) value at 5.7 cm.

Answers: 2

Answer

Physics, 23.06.2019 01:00

Are formed where bumps from two surfaces come into contact ?

Answers: 1

Answer

You know the right answer?

A long, fine wire is wound into a coil with inductance 5 mH. The coil is connected across the termin...

Questions