An engineer has designed the foundation for column system (20 columns) of a 5 story residential building. Preliminary excavation showed level of water below 3.5 m from ground level. The column loads were equal in all columns. Each column carried 2500 kN of axial load. The design engineer came up with the foundation size of 3.0 m  2.0 m for all columns. The assumed depth of footing was 1.5 m below the ground. Please calculate the appropriate boring depth from ground level for detail site investigation. Use ASCE procedure for your calculation.

Boring depth = 6.76m

Explanation:

Given Data:

No. of columns = 30

No. of storeys = 5

Water level =3.5m below ground level

Axial load = 2500kN

Foundation size = 3mx2m

Depth of footing = 1.5m = Df

Solution:

First we need to calculate estimated net stress on footing

As we know that: q₀ = P/A

By putting values we get

q₀ = 2500/(3*2) = 416.677 kN/m³

Now for the depth of bedrock from the bottom surface of footing,

D₃ = total depth of bedrock - Df = 100 -1.5 = 98.5m

Now for the calculation of D1, here D1 is the distance from bottom surface of footing to depth where change in vertical stress = Δσ¹ = (1/10)q₀ ---------equation (1)

Now, second diagram attached below is drawn according to stress distribution of 2V:1H

Δσ¹ = P/A¹ = (2500)/(3+z)(2+z) ---------equation (2)

From equation 1 and 2 we get

0.1*416.677 = 2500/(3+D1)(2+D1)

D1²+5D1 = 54

D1 = 5.2621 m

Now we will calculate D2 where we have Δσ¹ /σ₀¹ = 0.05

Now,

we will check this ratio for bottom most layer first(i.e. clay layer, ρsat=16.9kN/m³), if it is satisfied then O.K other wise we will continue procedure for top layers.

We have, Δσ¹ = σ₀¹(0.05)

First we need to find vertical stress σ₀¹ at depth z

σ₀¹ = (3.5*17) + 1.5*(ρsat-ρw)sand + (ρsat-ρw)clay*(D2-3.5)

By putting values we get

σ₀¹ = 59.5 + 13.035 _ 7.09D2 - 28.815

Putting it in equation 2 , we get

σ₀¹ = 2500/(3+D2)(2+D2) = 0.05 * (7.09D2 + 47.72)

By simplification, we get

7.09D₂³+83.167D₂²282.147D₂-49714 = 0

D₂ = 15.35 m

So from this calculation it is evident that Δσ¹ /σ₀¹ = 0.05 is at depth of 15.35m which is in clay layer, so no need to check in upper layers.

Now, for the calculation of boring depth depth,

Boring depth = D +Df

1st case = 5.26 + 1.5 = 6.76m

2nd case = 15.35 + 1.5 = 16.85m

13rd case = 98.5 + 1.5 = 100m

Boring depth = 6.76m

the answer is the first electromagnet (a). this is because it has more coils around the ferromagnetic material. increasing the number of coils increases the surface area in which the metal interacts with the current in the coil. this enables more atoms in the metal to become aligned hence becoming more magnetized.