Physics, 28.01.2020 21:47 carolynhstevens

The nucleus of the hydrogen atom has a radius of about 1 x 10−15 m. the electron is normally at a distance of about
5.3 x 10^−11 m from the nucleus.
assuming the hydrogen atom is a sphere with a radius of 5.3 x 10^−11 m.
find: (a) the volume of the atom, (b) the volume of the nucleus , and (c) the percentage of the volume of the atom that is occupied by the nucleus.

Answers: 2

Show answers

Another question on Physics

Physics, 21.06.2019 18:00

Aplane flies directly between two cities, a and b, which are separated by . from a to b, the plane flies into a headwind. on the return trip from b to a, the wind velocity is unchanged. the trip from b to a takes less than the trip from a to b. what is the airspeed of the plane, assuming it is the same in both directions

Answers: 1

Answer

Physics, 23.06.2019 03:30

Use the ratio form of kepler’s third law, = , and the data provided to determine the time it takes mars to orbit the sun. round your answer to the nearest tenth. earth’s orbital period = 1.0 earth year earth’s distance from the sun = 1.0 au mars’s distance from the sun = 1.5 au it takes mars about ⇒ 1.8 earth years to orbit the sun.

Answers: 2

Answer

Physics, 23.06.2019 04:31

Water flows through a garden hose which is attached to a nozzle. the water flows through hose with a speed of 2.19 m/s and through the nozzle with a speed of 19.8 m/s. calculate the maximum height (in m) to which water could be squirted if it emerges from the nozzle and emerges with the nozzle removed.

Answers: 1

Answer

Physics, 23.06.2019 08:30

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

Answer

You know the right answer?

The nucleus of the hydrogen atom has a radius of about 1 x 10−15 m. the electron is normally at a di...

Questions