Ahydrogen atom is excited from its ground state to then = 4 state. the atom subsequently emits three photons, one of which has a wavelength of 122 nm .

what are the wavelengths of the other two photons?

enter your answers in ascending order separated by commas.

   102 <122 <658 nm

Explanation:

The energy levels of the hydrogen atom are described by the Bohr model

        Eₙ = -13.606 / n²        [eV]

        n = 1, 2, 3, …

Where n is an integer

For an atom excited to the level n = 4

Let's look for the energy of these states

Let's use the Planck equation and the speed of light to find the wavelength

        E = h f

        c = λ f

        E = h c / λ

        λ = h c / E

Reductions

        1eV = 1.6 10⁻¹⁹ J

Let's start

n = 1

       E₁ = -13,606 eV

n = 2

      E₂ = -13.606 / 2² = -3.4015 eV

n = 3

      E₃ = -13.606 / 3² = -1.5118 eV

n = 4

      E₄ = -13.606 / 4² = - 0.8504 eV

Let's look for the wavelength of a specific energy

To pass the energy of eV to Joule multiply by 1.6 10-19 J

       λ = 6.63 10⁻³⁴ 3 10⁸ / E 1.6 10⁻¹⁹

       λ = 12.43125 10⁻⁷/E

Let's reduce the meter wavelength to nm 1 m = 10⁹ nm

The transitions are

State             DE = Ef-Ei (eV) lam (10-7 m) lam (nm)

Last  initial

4          1       -0.8504 - (-13606)  = 12.756     0.975       97.5

4           2      -0.8504 - (-3.4015) = 2.551       4.87       487

4           3      -0.8504 - (- 1.5118) = 0.661       18.80    1880

3           1       -1.5118 - (-13,606)  = 12,094       1.02       102

3           2      -1.5118 - (-3.4015)  = 1.890         6.58      658

2           1      -3.4015- (-13.606)  = 10.205       1.22       122

If the transition is to state n = 3, the transitions are

The energy of the transition in ascending order is

        12,094> 10,205> 1,890

The wavelengths are

          102 <122 <658 nm

most voltage drop calculators want the distance between the source and destination. then internally, they double it so both the source and return wires are calculated. but you need to know which distance the calculator uses so you're not half of what you should be or double what you should be.

most circuit breakers will not take a #6 directly, so the electrician will have to splice on a smaller pigtail. you also have to upsize the grounding wire when you upsized the ungrounded (hot) wire (see note in 250.122). this will preclude using most cable assemblies, as a cable with #6 copper will most likely only have a #10 grounding conductor. you need a #6 grounding conductor if the circuit is 20a. a #8 cable is no better, as it will have a #10 grounding conductor too. but most 20a breakers will take a #8 directly.

in your related post, you didn't say what type of load this is. if it is a light or heater, voltage drop won't be a big issue. if this is a motor, the current needs are huge at startup and the voltage drop can pose a problem. if this is a motor, knowing if the motor is under much load during startup will answer the voltage drop effect (a saw is easier to start than a compressor).