Physics, 28.09.2019 22:30 testedagent2823

Why is 30% recommended as the minimum michelson contrast?

Answers: 1

Show answers

Answers

Answer from: rohandpatil

Explained

Explanation:

Michelson contrast is used for patterns where the distribution of bright and dark segments is nearly equal.

It is given by:

$m= \frac{I_{max}-I{min}}{I_{max}+I{min} }$

where I_max = maximum illumination and I_min = minimum illumination

we know that

typically, I_min = 54% of I_max (general standard)

or I_min = 0.54 I_max

putting this value in above equation to get m

this approximately corresponds to m = 0.3 or 30%

hence, 30% recommended as the minimum Michelson contrast

Answer from: Quest

nec chapter 5 contains

c. information on special occupancy areas

nec chapter 6 covers

a. special equipment

which of the following rules contain the words shall or shall not and must be adhered to?

b. mandatory rules

which of the following rules identify actions that are allowed but not required and typically cover options or alternative methods?

c. optional rules

which of the following serves as the introduction to the nec and provides an overview of the book?

a. nec article 90

organizations that test products for safety are

c. nrtls

the nec is published by the

a national fire protection association

the nec is divided into

b. 9 chapters

the nec provides informative annexes for

c. informational materials and examples

two terms from nec article 100 that trainees should become familiar with are

b. labeled and listed

explanation:

Answer from: Quest

1) when you rub your hands together quickly, the kinetic energy is converted to mechanical energy.2) thermal energy from the sun travels to earth as infrared waves.3) energy is transferred through the matter of space by electromagnetic waves. 4) when a match is burned, chemical potential energy is converted to thermal and radiant energy. 5) seismicwaves are caused by back and forth movement , or vibration, of an object. 6) mechanicalenergy in an engine changes thermal energy into kinetic energy to make a car move.

Another question on Physics

Physics, 22.06.2019 00:30

Part f - example: finding two forces (part i) two dimensional dynamics often involves solving for two unknown quantities in two separate equations describing the total force. the block in (figure 1) has a mass m=10kg and is being pulled by a force f on a table with coefficient of static friction îľs=0.3. four forces act on it: the applied force f (directed î¸=30â above the horizontal). the force of gravity fg=mg (directly down, where g=9.8m/s2). the normal force n (directly up). the force of static friction fs (directly left, opposing any potential motion). if we want to find the size of the force necessary to just barely overcome static friction (in which case fs=îľsn), we use the condition that the sum of the forces in both directions must be 0. using some basic trigonometry, we can write this condition out for the forces in both the horizontal and vertical directions, respectively, as: fcosî¸â’îľsn=0 fsinî¸+nâ’mg=0 in order to find the magnitude of force f, we have to solve a system of two equations with both f and the normal force n unknown. use the methods we have learned to find an expression for f in terms of m, g, î¸, and îľs (no n).

Answers: 2

Answer

Physics, 22.06.2019 05:30

Can anybody me with this? ? (picture included.)

Answers: 1

Answer

Physics, 22.06.2019 22:00

A51 kg woman skis down a hill and her kinetic energy is 9.96e4 j. what is her speed?

Answers: 2

Answer

Physics, 23.06.2019 03:00

Suppose the house in question 3 is located in cleveland where the annual average solar flux is 160 w/m2 . if 10 m2 of solar panels operating at 20 percent efficiency were installed on this house to collect and store solar energy in the form of hot water: