Answers: 1
Physics, 22.06.2019 11:00
The dot diagram represents the motion of the motorcycle as it moves from left to right
Answers: 3
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
Physics, 23.06.2019 10:00
4. a car with a mass of 2,200 kg can accelerate from 0 to 30 m/s in 6 seconds. a. assuming all of the force generated by the engine goes into acceleration of the car, how much force is the engine producing? show your work. (6 points)
Answers: 1
Physics, 23.06.2019 13:30
If 150 kcal of heat raises the temperature of 2.0 kg of a material by 400 f°, what is the specific heat capacity of the material? 0.75 kcal/kg ∙ c° 1.35 kcal/kg ∙ c° 0.19 kcal/kg ∙ c° 0.34 kcal/kg ∙ c°
Answers: 1
Iapply acid to metal to create bubbles....
Mathematics, 18.03.2020 05:14
Mathematics, 18.03.2020 05:14
Chemistry, 18.03.2020 05:14
History, 18.03.2020 05:14
History, 18.03.2020 05:15
Mathematics, 18.03.2020 05:15
History, 18.03.2020 05:15
Engineering, 18.03.2020 05:16
Chemistry, 18.03.2020 05:17