Mathematics, 09.09.2021 01:20 andybiersack154

Please help me I’m struggling// have a good day

Answers: 1

Show answers

Another question on Mathematics

Mathematics, 21.06.2019 18:30

Anormally distributed data set has a mean of 176.3 and a standard deviation of 4.2. what is the approximate z-score for the data value of 167.9? 2.00 −2.00 8.4 −8.4

Answers: 2

Answer

Mathematics, 21.06.2019 22:00

How do you write a paragraph proof to prove that the corresponding angles shown are congruent

Answers: 2

Answer

Mathematics, 21.06.2019 22:00

Two numbers have a sum of -19. one number is x. what expression represents the other number?

Answers: 2

Answer

Mathematics, 22.06.2019 00:30

Pls as soon as ! will award brainliest and 20 ! also the answer is not 22.5 degrees! find the value of x in each case:

Answers: 3

Answer

You know the right answer?

Please help me I’m struggling// have a good day
...

Questions

Engineering, 26.07.2019 17:20

If i can live with a 3% probability of failure, select a ball bearing design (independent of shaft diameter that will carry a 120 ib load at 3000 rpm....

Engineering, 26.07.2019 17:20

Determine the diameter of a cylindrical capillary tube needed to observe a 0.4" rise for water if the contact angle is 12°...

Engineering, 26.07.2019 17:20

If a cutting operation is performed at a feed rate of 5 in/min, and the feed is 0,005 in/rev, then the spindle rpm is: i. 5000 rpm. i. 1000 rpm. ili....

Engineering, 26.07.2019 17:20

Describe the general steps in the journal bearing design procedure. outline approach with substeps identified is fine....

Engineering, 26.07.2019 17:20

How are the pressure angle, pitch circle and base circle for a gear set related?...

Engineering, 26.07.2019 17:20

You need to design a compound reverted gear train with a 25: 1 gear ratio. (a) explain how you would go about developing this design. (b) if you were...

Engineering, 26.07.2019 17:20

One of the following is an extensive property: a)- density b)- volume c)- pressure d)-none of the above...

Engineering, 26.07.2019 17:20

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

Engineering, 26.07.2019 17:20

Tool wear rate decreases with increasing: i. machining velocity and work material hardness. ii. cutting tool hardness. ii. none of the above. iv. not...

Engineering, 26.07.2019 17:20

Define the following terms. a drawing with the terms labeled would also be where appropriate. a. pitch circle/pitch diameter b. pinion/gear c. base c...

Engineering, 26.07.2019 17:20

5kg of wood is burnt in an insulated room. take the walls of the room as well as the wood as the system. the internal energy of the room will increase...

Engineering, 26.07.2019 17:20

The hardness of a cutting tool increases with increasing temperature. thus, it is always convenient to machine at higher speeds that lead to higher te...

Engineering, 26.07.2019 17:20

What are the independent and dependent variables that are taken into account during journal bearing design?...

Engineering, 26.07.2019 17:20

You are provided with an epicyclic (planetary) gear train with the following 30, 20 and 70 teeth on the sun, planet and ring gear respectively. (a) dr...

Engineering, 26.07.2019 17:20

What is a partial bearing? what is a loading situation that might lead you to use a partial bearing? how did this tie into beauchamp tower's experim...

Engineering, 26.07.2019 17:20

Define and give a few benefits of each of three gear train design options?...

Engineering, 26.07.2019 17:20

The atmospheric pressure at the top and the bottom of a mountain are read to be 93.8 kpa and 100.5 kpa respectively. if the average density of air is...

Engineering, 26.07.2019 17:20

What are some of the assumptions that were used in developing the 1d reynolds flow equation?...

Engineering, 26.07.2019 17:20

Acar engine rotates at a speed of 3500 rpm and transmits 290 kw. determine the torque applied to the crankshaft of the car a)- 791.2 n. m b)- 1108 n....

Engineering, 26.07.2019 17:20

The pressure of a fluid at rest changes with vertical distance but remains the same in the horizontal direction a)-true b)-false...

More questions: Mathematics Another questions