Pls help me this is hard

l= 16

b=14

h=20

area to be painted= 2(l+b)h

=2(30)20

60×20

1200sq feet

the range of a function is the range of y-values for which it is defined, or exists. given that we are only looking at the y-values, we can already discount the first two answers as they deal with the domain of the function (range of x-values).

now, what we need to do is find the smallest and highest y-values for which the function is defined. if you'd like, you could take a ruler and start at the very bottom of the graph, find the lowest point, then move the ruler higher and higher until you reach the highest point. doing so either in your head or with an actual ruler, we can see that the lowest y-value is -5 and the highest y-value is -1.

the question now remains as to whether they are included in the range (fourth answer) or excluded (third answer). the key here is to recognise whether they are marked with an open or a closed circle. since both (-2, -5) and (2, -1) are marked with a closed circle, they are points that exist on the graph and are thus included in the range (note that if they were marked with an open circle like (4, -2) then that would signify that there is a break in the graph at that point).

thus, the fourth answer, (y | -5 ≤ y ≤ -1), is correct.

also note that usually it is good practice to scan your eye inbetween the highest and lowest point for any breaks in the graph - we do have one here at (4, -2), however -2 is still included in the range because there is another point that is included in the graph with the same y-value, ie. point (1, -2).

i hope that but if you require any further explanation don't hesitate to comment below.

part a

answer: a reasonable domain is where n is a real number. so n can be between 0 and 10. both endpoints are included.

work shown:

n is the number of days after the experiment starts. the smallest n can be is n = 0 which means that 0 days have gone by, and we're at the start. to find out how large n should be, then replace f(n) with 16.13 and solve for n. use logarithms to isolate the exponent.

f(n) = 12*(1.03)^n

16.13 = 12*(1.03)^n

16.13/12 = (1.03)^n

1.34416666666667 = (1.03)^n

(1.03)^n = 1.34416666666667

log[ (1.03)^n ] = log[ 1.34416666666667 ]

n*log[ 1.03 ] = log[ 1.34416666666667 ]

n = log[ 1.34416666666667 ]/log[ 1.03 ]

n = 10.0062999823929

this rounds to n = 10 which is fairly close but not 100% perfect. so this is the largest n can be.

note: if you plug n = 10 into f(n), you'll get roughly 16.127 which rounds to 16.13 (this comes up again in part c)

=====================================

part b

answer: the y intercept is 12. it represents the starting height of the plant in cm.

work shown:

plug n = 0 into the f(n) function. simplify

f(n) = 12*(1.03)^n

f(0) = 12*(1.03)^0

f(0) = 12*(1)

f(0) = 12

on day n = 0, aka the starting point, the height f(n) is 12 cm

=====================================

part c

answer: the average rate of change is approximately 0.43061036458991 (round however you need to). this represents the average growth rate from day n = 3 to day n = 10. so the plant grew roughly 0.43 cm per day during this timespan, assuming you round to 2 decimal places.

work shown:

compute f(3)

f(n) = 12*(1.03)^n

f(3) = 12*(1.03)^3

f(3) = 13.112724 < we'll use this later

compute f(10)

f(n) = 12*(1.03)^n

f(10) = 12*(1.03)^10

f(10) = 16.1269965521294 < we'll use this later

now use the formula below with a = 3 and b = 10

aroc = average rate of change

aroc = [ f(b) - f(a) ]/[ b - a ]

aroc = [ f(10) - f(3) ]/[ 10 - 3 ]

aroc = (16.1269965521294 - 13.112724)/(10 - 3)

aroc = 3.0142725521294/7

aroc = 0.43061036458991

round this however you need to

note: the plant grew approximately 3.01 cm over 7 days, so roughly 0.43 cm per day is the average growth rate (if you were to round to 2 decimal places).