subject
Mathematics, 15.02.2021 20:50 cynthiagutierrez65

Which statement is correct? A. MG is perpendicular to TB
B. MT is skew to GB
C. BT is transversal to GB and BG
D. TM perpendicular to BG


Which statement is correct? A. MG is perpendicular to TB B. MT is skew to GB C. BT is transversa

ansver
Answers: 2
Show answers

Another question on Mathematics

question
Mathematics, 21.06.2019 16:00
On a piece of paper graph f(x)=5•(0.4)^x
Answers: 1
Answer
question
Mathematics, 21.06.2019 16:40
This question awards 100 ! i really don’t want to fail i will also mark you !
Answers: 2
Answer
question
Mathematics, 21.06.2019 17:30
Janet drove 300 miles in 4.5 hours. write an equation to find the rate at which she was traveling
Answers: 2
Answer
question
Mathematics, 21.06.2019 17:40
Bradley hikes 12 miles in 3 hours. in relation to bradley’s hike, which statement describes the expression
Answers: 2
Answer
You know the right answer?
Which statement is correct? A. MG is perpendicular to TB
B. MT is skew to GB
C. BT is...
Questions
question
Engineering, 26.07.2019 20:10
Air initially at 15 psla and 60 f is compressed to 75 psia and 400 f. the power input to air under steady state condition is 5 hp and heat loss of 4 b...
question
Engineering, 26.07.2019 20:10
How does the thermal efficiency of an ideal cycle, in general, compare to that of a carnot cycle operating between the same temperature limits?...
question
Engineering, 26.07.2019 20:10
Agas turbine cycle using brayton cycle with both intercooler and regenerators air and split ideal compressor and turbine, enters in the compressor at...
question
Engineering, 26.07.2019 20:10
Define the isentropic efficiency for each of the following 3. a. i. adiabatic turbine ii. adiabatic compressor iii. adiabatic nozzle...
question
Engineering, 26.07.2019 20:10
What causes a shock to detach from the surface of an object?...
question
Engineering, 26.07.2019 20:10
Consider two solid blocks, one hot and the other cold, brought into contact in an adiabatic container. after a while, thermal equilibrium is establish...
question
Engineering, 26.07.2019 20:10
Steam at 500 psia and 600 f is cooled at constant volume to the state of 100 psia. the heat removed from the steam enters the environment at 60 f. fin...
question
Engineering, 26.07.2019 20:10
Avolcanic plume puts ash into the atmosphere to altitude of 1m. the characteristic ash particle is a sphere with a diameter of 40 um and has a density...
question
Engineering, 26.07.2019 20:10
Consider a steam power plant that operates on the ideal reheat rankine cycle. the plant maintains the boiler at 5,000 kpa, the reheat section at 1,200...
question
Engineering, 26.07.2019 20:10
Pressurized steam at 540 k flows through a long, thin-walled pipe of 0.6-m diameter. the pipe is enclosed in a concrete casing that is of square cross...
question
Engineering, 26.07.2019 20:10
Rank the six microstructures of steel in general order of least ductile to most ductile.(bainite, coarse pearlite, fine pearlite, martensite, spheroid...
question
Engineering, 26.07.2019 20:10
In regard to low pressure die casting, high pressure die casting and squeeze casting of aluminium alloys, briefly compare the following process charac...
question
Engineering, 26.07.2019 20:10
A2d, incompressible flow field is described by the stream function φ= -(ax^2-ay^2). a. is the flow possible? b. is the flow field a potential flow fi...
question
Engineering, 26.07.2019 20:10
(a) briefly describe, aided with schematic drawings, the operation principles of the two 6. powder bed (selective laser melting and selective electron...
question
Engineering, 26.07.2019 20:10
Steam at a pressure of 15 bar and a temperature of 320 °c is contained in a large vessel. connected to the vessel through a valve is a turbine followe...
question
Engineering, 26.07.2019 20:10
Awaste gas stream containing 190 ppm by volume ) vinyl chloride is to be treated with activated carbon ina packed bed at a rate of 20 m3/min to reduce...
question
Engineering, 26.07.2019 20:10
Casting of a plate is made in a metal mould where heat transfer is controlled at the mould- metal interface. ignore the superheat of the liquid metal...
question
Engineering, 26.07.2019 20:10
Consider two long, poles of same diameter and uniform cross sectional area throughout its length but different materials. the ends of each rod is atta...
question
Engineering, 26.07.2019 20:10
What is the quality of a two-phase liquid-vapor mixture of h20 at 20 °c with a specific volume of 10 m^3/kg?...
question
Engineering, 26.07.2019 20:10
Consider cutting tool materials, answer which cutting material is suitable, considering manufacturing costs, for each of the major metallic alloy (al...
More questions: Mathematics Another questions
Questions on the website: 13722360
See results (0)