![subject](/tpl/images/cats/User.png)
Engineering, 12.03.2022 01:30 austintules2005
You're looking at a fault trace in the field. You observe a polished surface with linear grooves on it, and fine powder next to it. In more technical terms, what are you seeing? Choose one: A. slip lineation, slickensides, and fault breccia B. shear zone, fault gouge, and fault breccia C. slickensides, slip lineations, and fault gouge D. slickensides, fault breccia, and fault gouge
![ansver](/tpl/images/cats/User.png)
Answers: 1
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Water at 70°f and streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream. 0 psia is heated in a chamber by mixing it with saturated water vapor at 20 psia. if both streams enters the mixing chamber at the same mass flow rate, determine the temperature and the quality of the existing system.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Shafts are machine elements that are used to a) carry axial loads b) direct shear loads c) transmit power d) rotate at constant speed e) none of the above circular and square shafts subjected to the same torque under the same circum behave a) the same way b) almost the same way
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Hydraulic fluid with a sg. of 0.78 is flowing through a 1.5 in. i.d. pipe at 58 gal/min. the fluid has an absolute viscosity of 11.8 x 105 lbf-sec/ft2. is the flow laminar, turbulent or within the critical range? give both a numerical reynolds number and a term answer.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Water at the rate of 1 kg/s is forced through a tube with a 2.5 cm inner diameter. the inlet water temperature is 15°c, and the outlet water temperature is 50°c. the tube wall temperature is 14°c higher than the local water temperature all along the length of the tube. what is the length of the tube?
Answers: 3
You know the right answer?
You're looking at a fault trace in the field. You observe a polished surface with linear grooves on...
Questions
![question](/tpl/images/cats/pravo.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 03.09.2020 22:01
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
English, 03.09.2020 22:01
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 03.09.2020 22:01
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 03.09.2020 22:01
![question](/tpl/images/cats/mat.png)
Mathematics, 03.09.2020 22:01
![question](/tpl/images/cats/mat.png)
Mathematics, 03.09.2020 22:01