![subject](/tpl/images/cats/User.png)
Engineering, 24.02.2022 15:20 KieraKimball
A) A second fault surface exists exactly 100 meters elevation below the one depicted below. Draw its
map expression (the equivalent of the red line for the second fault).
b) A horizontal bed is cut by these faults. In the footwall of the lowest fault it is at an elevation of 350 m.
In the footwall of the higher fault it is at an elevation of 290 m, and in the hanging wall of the higher
fault it is at 210 m elevation. Draw in the map expression of the horizontal bed as it is cut by these two
faults. You will need to interpolate between the given contour lines. Remember that the footwall is the
block beneath a dipping fault, and the hanging wall is that above.
100 m
500 m
N
400 m
300 m
m
200 m
100 m
500 m
500 m
400 m
300 m
300 m
200 m
200 m
100 m
100 m
geologic contact
![ansver](/tpl/images/cats/User.png)
Answers: 1
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Condition monitoring is a major component of. (clo4) a)- predictive maintenance. b)-preventive maintenance c)-proactive maintenance d)-reactive maintenance.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Journeyman training is usually related (clo2) a)-to specific tasks b)-to cost analysis of maintenance task c)-to control process to ensure quality d)-to installation of machinery
Answers: 2
You know the right answer?
A) A second fault surface exists exactly 100 meters elevation below the one depicted below. Draw its...
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 24.03.2021 21:00
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 24.03.2021 21:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 24.03.2021 21:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 24.03.2021 21:00
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 24.03.2021 21:00
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)