![subject](/tpl/images/cats/User.png)
Engineering, 30.11.2021 22:00 samantha2883
An ideal Diesel cycle has a thermal efficiency of 60.7% and a cutoff ratio of 1.8. Using cold-air-standard assumptions, determine the compression ratio r (to the nearest 0.1).
![ansver](/tpl/images/cats/User.png)
Answers: 3
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
How much power could a wind turbine produce if it had the following specifications? cp = 0.45 -d=1.2kg/m3 d=50m v 5m/s
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 05:10
Apipe of diameter 200 mm (constant) carrying water with an 5 mis and total head is density 1000 kg/m ) with velocity tpward slope. at a certain point, where the elevation is 5 m above a datum,the 21.5 m. a) determine the pressure of the pipe at 5m elevation. determine the pressure at elevation 10m (above same datum) if the of total head at 5m elevation.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 05:20
The inner surface of a 0.25m thick brick wall of a furnace is kept at 810ºc, when the outside surrounding air is at 22ºc. the convective heat transfer coefficient of the outer surface is 12 w/m2k and the thermal conductivity of the brick is 0.865 w/mk.neglect the convective resistance for the inner side of the furnace and assume that the problem is steady state and thermal radiation is neglected. (a)-sketch the system and calculate the rate of heat loss per unit wall area. (b)-calculate the temperature of the outer wall surface.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 05:20
Acantilever of 3 m length with a t-shaped cross-section is loaded by three concentrated loads: w,-80 n at the free end, w 30 n, and w,-60 n at a distance of 1 m from the free end. all loads are applied at the outer edges of the flange as indicated in the sketch below. (a)-determine the maximum torsional shear stresses in the flange and in the web at distances 0.5 m and 2.5 m from the free end (sections i and ii marked in the sketch) b)- determine thefh end cross section assuming a shear modulus of 210 gpa.
Answers: 3
You know the right answer?
An ideal Diesel cycle has a thermal efficiency of 60.7% and a cutoff ratio of 1.8. Using cold-air-st...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 07.12.2020 19:20
![question](/tpl/images/cats/fizika.png)
Physics, 07.12.2020 19:20
![question](/tpl/images/cats/es.png)
Spanish, 07.12.2020 19:20
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 07.12.2020 19:20
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 07.12.2020 19:20
![question](/tpl/images/cats/istoriya.png)
History, 07.12.2020 19:20
![question](/tpl/images/cats/mat.png)
Mathematics, 07.12.2020 19:20
![question](/tpl/images/cats/fizika.png)
Physics, 07.12.2020 19:20
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 07.12.2020 19:20
![question](/tpl/images/cats/mat.png)
Mathematics, 07.12.2020 19:20
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/en.png)
English, 07.12.2020 19:20
![question](/tpl/images/cats/ap.png)
Advanced Placement (AP), 07.12.2020 19:20