![subject](/tpl/images/cats/User.png)
Engineering, 01.08.2021 16:40 kelseiroll8554
A gear component (0.2% C) is carburized with C for increased hardness. By specification, a carbon concentration of 0.75% C is required at an 80 um depth. Calculate the time required (ir hours) at 1100°C with the gas surface concentration of 1.3 % C. D=5x10-13 m2/s. Show relevant steps how you arrived at the answer Comment on whether the suggested carburizing time of 3 hours is sufficient, also mention the calculated time in hours
![ansver](/tpl/images/cats/User.png)
Answers: 1
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 14:10
When at a point two solid phase changes to one solid phase on cooling then it is known as a) eutectoid point b) eutectic point c) peritectic point d) peritectoid point
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Agas mixture consists of 8 kmol of h2 and 2 kmol of n2. determine the mass of each gas and the apparent gas constant of the mixture.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20
To design a steam turbine to produce 12,000 hp power. a engineer comsiders using a steady state stean low st 1160fr and engineer considers using a steady state steam flow at 1160°r and 450 psia to drive this steam turbine. the exhaust of the steam is cooled by the lake (vacuum). heat losing to the surroundings is measured at a rate of 555.55 btu/s. (a) sketch the system with the given conditions. (b) neglecting kinetic and potential energy changes from inlet to exit, determine the volumetric flow rate of the steam at the inlet, (ft'/hr). must clearly show unit conversions at crtical terms.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 05.07.2019 23:20
Which one of the following faults cause the coffee in a brewer to keep boiling after the brewing cycle is finished? a. an open circuit in the heating element b. a short circuit at the terminals c. welded contacts on the thermostat d. a leak around the gasket
Answers: 3
You know the right answer?
A gear component (0.2% C) is carburized with C for increased hardness. By specification, a carbon co...
Questions
![question](/tpl/images/cats/istoriya.png)
History, 17.12.2020 05:40
![question](/tpl/images/cats/en.png)
English, 17.12.2020 05:40
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
Health, 17.12.2020 05:40
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 17.12.2020 05:40
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 17.12.2020 05:40
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
English, 17.12.2020 05:40
![question](/tpl/images/cats/mat.png)
Mathematics, 17.12.2020 05:40
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 17.12.2020 05:40
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 17.12.2020 05:40
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 17.12.2020 05:40
![question](/tpl/images/cats/biologiya.png)
Biology, 17.12.2020 05:40
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 17.12.2020 05:40