subject
Engineering, 28.07.2021 04:30 jayjinks976

Consider the 2D motion of a rocket moving around the Earth. Consider Earth as being stationary and the attractive force i induces on the rocket is directed towards the center of the Earth and has a magnitude of In the equation r is the current distance of the rocket from the center of the Earth . RE 6371 km is the radius of the Earth m is the mass of the rocket g 9.81 m/s2 is the usual acceleration due to gravity (on the Earth's surface) a) Write the equations of motion of the rocket in an appropriate polar coordinate system. b) Integrate the equations of motion for the system numerically using MATLAB and ode45 for the conditions shown below. The initial distance between the rocket and the Earth is ro. The initial velocity of the rocket towards the center of the Earth and perpendicular to it are given by vr and ve respectively. Assume that the angle 8 is zero initially and that ro-5RE and vr 0. Carry out the integration at a time step of 10s for 80,000 time steps (i. e., a total simulation time of 800,000 seconds) for each of the initial velocities specified below: For each condition, plot the trajectory of the rocket for the requested time and plot the two components v and ve of the velocity as a function of time. For the trajectory, you may plot the two Cartesian coordinates defined by x = r cos θ an yrsin 6 that you can evaluate numerically once you have the values of r and Note that the trajectories will be (a) a circle, (b) an ellipse, (c) a parabola, and (d) a hyperbola. Case (c) is the escape velocity - the lowest velocity for which the particle will leave the Earth's attractive influence. Use the MATLAB "axis equal" command in the trajectory plots, to see the shape of trajectory in proper scale.

ansver
Answers: 1

Another question on Engineering

question
Engineering, 04.07.2019 18:10
Water at 70°f and streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream. 0 psia is heated in a chamber by mixing it with saturated water vapor at 20 psia. if both streams enters the mixing chamber at the same mass flow rate, determine the temperature and the quality of the existing system.
Answers: 2
question
Engineering, 04.07.2019 18:10
Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.
Answers: 3
question
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
question
Engineering, 04.07.2019 18:10
Carbon dioxide gas expands isotherm a turbine from 1 mpa, 500 k at 200 kpa. assuming the ideal gas model and neglecting the kinetic and potential energies, determine the change in entropy, heat transfer and work for each kilogram of co2.
Answers: 2
You know the right answer?
Consider the 2D motion of a rocket moving around the Earth. Consider Earth as being stationary and t...
Questions
question
Mathematics, 04.12.2020 22:50
question
Mathematics, 04.12.2020 22:50
question
Mathematics, 04.12.2020 22:50
question
Mathematics, 04.12.2020 22:50
question
Mathematics, 04.12.2020 22:50
Questions on the website: 13722361