![subject](/tpl/images/cats/User.png)
Engineering, 20.05.2021 20:10 diablo666
Look this will probably get reported for no reason whatsoever but i know there are a lot of people on this website looking for a gf or bf so if you are instead of using to look use this link to pad let https://pad let. com/xhennhj/w2z9t9c66pme8vrq
![ansver](/tpl/images/cats/User.png)
Answers: 1
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 15:10
Apiston-cylinder with a volume of 0.25 m3 holds 1 kg of air (r 0.287 k/kgk) at a temperature of 100 c. heat transfer to the cylinder causes an isothermal expansion of the piston until the volume triples. how much heat is added to the piston-cylinder?
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200°c and outer surface temperature of the insulation to be 15°c. calculate the thickness of insulation required.
Answers: 3
You know the right answer?
Look this will probably get reported for no reason whatsoever but i know there are a lot of people o...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 23.07.2019 19:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)
History, 23.07.2019 19:30
![question](/tpl/images/cats/mat.png)
Mathematics, 23.07.2019 19:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 23.07.2019 19:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 23.07.2019 19:30
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 23.07.2019 19:30
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 23.07.2019 19:30
![question](/tpl/images/cats/ekonomika.png)
Business, 23.07.2019 19:30
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
History, 23.07.2019 19:30