![subject](/tpl/images/cats/User.png)
Engineering, 02.04.2021 08:40 Savageboyn
In your own words and using complete sentences, describe each of the steps in cruising timber using a Biltmore stick.
Step 1:
Step 2:
Step 3:
Step 4:
Step 5:
![ansver](/tpl/images/cats/User.png)
Answers: 2
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 23:20
Two technicians are discussing the intake air temperature (iat) sensor. technician a says that the computer uses the iat sensor as a backup to the engine coolant temperature (ect) sensor. technician b says that the powertrain control module (pcm) will subtract the calculated amount of fuel if the air measures hot. who is correct
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Thermal stresses are developed in a metal when its a) initial temperature is changed b) final temperature is changed c) density is changed d) thermal deformation is prevented e) expansion is prevented f) contraction is prevented
Answers: 2
You know the right answer?
In your own words and using complete sentences, describe each of the steps in cruising timber using...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 18.11.2020 21:20
![question](/tpl/images/cats/mat.png)
Mathematics, 18.11.2020 21:20
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/health.png)
Medicine, 18.11.2020 21:20
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/ap.png)
Advanced Placement (AP), 18.11.2020 21:20
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 18.11.2020 21:20
![question](/tpl/images/cats/health.png)
Health, 18.11.2020 21:20
![question](/tpl/images/cats/mat.png)
Mathematics, 18.11.2020 21:20
![question](/tpl/images/cats/mat.png)
Mathematics, 18.11.2020 21:20
![question](/tpl/images/cats/mat.png)
Mathematics, 18.11.2020 21:20
![question](/tpl/images/cats/geografiya.png)
Geography, 18.11.2020 21:20
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 18.11.2020 21:20
![question](/tpl/images/cats/User.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 18.11.2020 21:20