Engineering, 25.03.2021 20:10 leapfroggiez
To design a dc bias circuit, some reasonable approximations may be used. The first
assumption is the voltage from emitter to ground. VE is typically one-fifth to one-tenth of the
supply voltage, VCC. Selecting the emitter voltage in this way will permit calculating the
emitter resistance, RE and then the collector resistance, RC by using the following equations:
VE ≈ 1 / 10 VCC
RE ≈ VE / IC
RC = (VCC - VCE - VE) / IC
Hence, the base voltage is approximately equal to the emitter voltage,
or more exactly, VB = VE + VBE.
Finally, determine the values for the base resistors, RB1 and RB2 by approximating
RB2 ≤ 1/ 10 ( βRE )
RB1 can be obtained by using the following equation,
VB = RB2
/ (RB2 + RB1 ) ( VCC )
Now, by referring to the proposed circuit as shown in Figure 1, select appropriate values for
RB1
, RB2
, RC and RE. Simulate the circuit and print the output waveform, Vo for a sinusoidal
input signal of 10mV at frequency 1kHz.​
Answers: 1
Engineering, 04.07.2019 18:10
Acompressor receives the shaft work to decrease the pressure of the fluid. a)- true b)- false
Answers: 3
Engineering, 04.07.2019 18:20
Asolid cylinder is concentric with a straight pipe. the cylinder is 0.5 m long and has an outside diameter of 8 cm. the pipe has an inside diameter of 8.5 cm. the annulus between the cylinder ad the pipe contains stationary oil. the oil has a specific gravity of 0.92 and a kinematic viscosity of 5.57 x 10-4 m2/s. most nearly, what is the force needed to move the cylinder along the pipe at a constant velocity of 1 m/s?
Answers: 3
Engineering, 04.07.2019 18:20
An engine runs on the ideal diesel cycle. the cycle has a compression ratio of 20 and a cutoff ratio of 2. the highest temperature in the cycle is 1200 k. if the heat into the system is 300 kj/kg of working fluid and using variable specific heats determine the work produced per mass of working fluid
Answers: 3
Engineering, 04.07.2019 19:10
Arigid tank contains 10 kg of air at 137 kpa (abs) and 21°c. more air is added to the tank until the pressure and temperature rise to 242 kpa (abs) and 32°c, respectively. determine the amount of air added to the tank. [r-0.287 kj/kg k]
Answers: 3
To design a dc bias circuit, some reasonable approximations may be used. The first
assumption is th...
Mathematics, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Biology, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Biology, 18.09.2020 22:01
Business, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
History, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
History, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Mathematics, 18.09.2020 22:01
Geography, 18.09.2020 22:01