Engineering, 22.02.2021 06:40 jamesmcfarland

LEARNING ACTIVITY SHEET Bantayan National High School
EIM 11- Summative Test for Q2 Week 3&4
Name:
Year and Section :
A. Direction: Select from he given choices the best answer. Write only the corresponding letter as your answer in the blank provided before the
number. Use this paper as your answer sheet.
1. It is used to test/check the continuity of the circuit.
a. Ohmmeter b. Ammeter c. Voltmetdewer d. Wattmeter
2. Is a physical device used to connect electronic test equipment to a device under test.
a. Test probes
b. Plug
c. Pen tester d. None of these
3. A device inserted to a convenience outlet to conduct electric current.
a. Plug b. Continuity tester c. Test light d. None of these
4. Is a stranded wire used to temporary wiring installation and commonly used in extension cord assembly.
a. Duplex cord
b. Plug
c. Bulb guard d. None of these
5. It is a pocket size tool used to test the line wire or circuit if there is a current in it.
a. Test light
b. Plug
c. Continuity tester d. None of these
6. An instrument used to measure the amount of electrical current intensity in a circuit.
a.) voltmeter b.)ammeter c.) micrometer d.) ohmmeter
7. A pocket-sized tool used to test the line wire or circuit if there is current in it.
a.) test light
b.) wire gauge
c.) ruler
d.) pull-push rule
8. A measuring tool used to measure the length of an object in centimeter in it.
a.) test light
b.) wire gauge
c.) ruler
d.) pull-push rule
9. It is used to measure the diameter of wires/ conductors in circular mils. It can measure small and big
sizes of wires and cables.
a.) voltmeter b.)ammeter c.) micrometer d.) ohmmeter
10. It is used to measure the voltage, resistance and current of a circuit. It is connected in parallel or series with the
circuit depending on what to measure.
a.) volt-ohm-milliameter b.) micrometer c.) ohmmeter d.) ammeter
11. It is a measuring tool used to measure length, width and thickness of short flat object and in sketching straight
linae

Answers: 1

Show answers

Answers

Answer from: CheddaDsk

1. It is used to test/check the continuity of the circuit

a. Ohmmeter

2. Is a physical device used to connect electronic test equipment to a device under test

a. Test probes

3. A device inserted to a convenience outlet to conduct electric current

a. Plug

4. Is a stranded wire used to temporary wiring installation and commonly used in extension cord assembly

a. Duplex cord

5. It is a pocket size tool used to test the line wire or circuit if there is a current in it.

a. Test light

6. An instrument used to measure the amount of electrical current intensity in a circuit

b. Ammeter

7. A pocket sized tool used to test the line wire or circuit if there is current in it.

a. Test light

8. A measuring tool used to measure the length of an object in centimeter in it

b) Ruler

9. It is used to measure the diameter of wires/conductors in circular mills. It can measure small and big sizes of wires

a. Micrometer

10. It is used to measure the voltage, resistance and current of a circuit. It is connected in parallel or series with the circuit depending on what to measure

a) Volt-Ohm-milliammeter

11. It is the measuring tool used to measure length, width and thickness of short object and in sketching straight line

Foot rule/ ruler

Explanation:

1. An Ohmmeter tests resistance of a circuit and therefore, indicates if the circuit has continuity (connectivity) by measuring the resistance to the current it sends through the circuit, while the circuit power is switched off

2. A test probe connects a testing equipment to a Device Under Test (DUT)

3. A plug is used to connect an electric appliance to the mains power supply by fitting it into the mains power outlet

4. A duplex cord is used for temporary wiring to supply power in an extension cord assembly

5. A test light is used to determine if a circuit has electric current flowing in it

6. An ammeter measures the amount of direct or alternating current flowing in a circuit

7. Test light is used to check the presence of an electric current in a circuit

8. A ruler is used to measure length and it is marked in cm or in

9. A micrometer measures the diameter of wires placed in between the anvil and spindle

10. A Volt-Ohm-Milliammeter (VOM), is also known as a multimeter that measures voltage, current, and resistance of a circuit

11. A foot rule/ ruler, measures the dimensions of objects that are flat and short

Answer from: Quest

explanation:

i don't understand really? can u provide more information

u should make a machine that can make ice cream fresh!

Answer from: Quest

answer: jesus loves you

explanation:

Another question on Engineering

Engineering, 04.07.2019 18:10

An air conditioning system consist of a 5 cm diameter pipe, operating at a pressure of 200 kpa. the air initially enters the pipe at 15°c with a velocity of 20 m/s and relative humidity of 80%. if the heat supply throughout the process is 960 w, determine the relative humidity and the temperature at the outlet

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Different types of steels contain different elements that alter the characteristics of the steel. for each of the following elements, explain what the element does when alloyed with steel.

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Ajournal bearing has a journal diameter of 3.250 in with a unilateral tolerance of 20.003 in. the bushing bore has a diameter of 3.256 in and a unilateral tolerance of 0.004 in. the bushing is 2.8 in long and supports a 700-lbf load. the journal speed is 900 rev/min. find the minimum oil film thickness and the maximum film pressure for both sae 20 and sae 20w-30 lubricants, for the tightest assembly if the operating film temperature is 160°f. a computer code is appropriate for solving this problem.

Answers: 3

Answer

You know the right answer?

LEARNING ACTIVITY SHEET Bantayan National High School
EIM 11- Summative Test for Q2 Week 3&...

Questions