Engineering, 23.12.2020 23:50 zahwaahmaf

Chapter 19: Diesel Engine Operation and Diagnosis -Chapter Quiz 1. How is diesel fuel ignited in a warm diesel engine?
A. Glow plugs
B. Heat compression
C. Spark plugs
D. Distributor-less ignition system

2. Which type of diesel injection produces less noise?
A. Indirect injection (IDI)
B. Common rail
C. Direct injection
D. Distributor injection

3. Which diesel injection system requires the use of a glow plug?
A. Indirect injection (IDI)
B. High pressure common rail
C. Direct injection
D. Distributor injection

4. The three phases of diesel ignition include .
A. Glow plug ignition, fast burn, slow burn
B. Slow burn, fast burn, slow burn
C. Ignition delay, repaid combustion, controlled combustion
D. Glow plug ignition, ignition delay, controlled combustion

5. What fuel system component is used in a vehicle equipped with a diesel engine that is seldom used on the same vehicle when it is equipped with a gasoline engine?
A. Fuel filter
B. Fuel supply line
C. Fuel return line
D. Water-fuel separator

6. The diesel injection pump is usually driven by a .
A. Gear off the camshaft
B. Belt off the crankshaft
C. Shaft drive off of the crankshaft
D. Chain drive off of the camshaft

7. Which diesel system supplies high-pressure diesel fuel to all the injectors all of the time?
A. Distributor
B. Inline
C. High-pressure common rail
D. Rotary

8. Glow plugs should have high resistance when and lower resistance when .
A. Cold/warm
B. Warm/cold
C. Wet/dry
D. Dry/wet

9. Technician A says that glow plugs are used to help start a diesel engine and are shut off as soon as the engine starts. Technician B says that the glow plugs are turned off as soon as a flame is detected in the combustion chamber. Which Technician is correct?
A. Technician A only
B. Technician B only
C. Both Technicians A and B
D. Neither Technicians A NOR B

10. What part should be removed to test cylinder compression on a diesel engine?
A. An injector
B. An intake valve rocker arm and stud
C. An exhaust valve
D. A glow plug

Answers: 3

Show answers

Another question on Engineering

Engineering, 03.07.2019 19:30

When using the ohmmeter function of a digital multimeter, the leads are placed in what position relative to the component being tested? a. parallel b. control c. series d. line

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

What are the two (02) benefits, which may result from a successful implementation of preventive maintenance (pm) program in an organization? (clo3)a)- lean manufacturing b)-overlapping responsibilities c)-the planner is not qualified d)-accurate contractor information e)-reduction in equipment redundancies f)-accurate stores information

Answers: 3

Answer

You know the right answer?

Chapter 19: Diesel Engine Operation and Diagnosis -Chapter Quiz 1. How is diesel fuel ignited in a...

Questions