Engineering, 10.11.2020 01:00 brendaesme

A block is sliding down an incline of 60 degrees as shown in the figure below. The coefficient of friction, μ , of the surface of the incline plane is 0.3. The frictional force is = μ where is the normal force. The weight of the block is W. Assume the acceleration due to gravity is 9.8 m/ 2 (a) Provide the expression for the component for the Weight force in the direction along the incline plane.
(b) Provide the expression for the component for the Weight force in the direction perpendicular to the incline plane.
(c) Provide the expression for the normal force in terms of W.
(d)
Provide the expression for in terms of W.
(e) Provide the equation for the sum of the forces in the direction along the incline plane (include appropriate signs).
(f) Provide the equation for the sum of the forces in the direction perpendicular to the incline plane (include appropriate signs).
(g) What is the value for acceleration of the block along the incline plane?
(h) How far (in meters) will the block slide in 10 seconds if it is released from rest?

A block is sliding down an incline of 60 degrees as shown in the figure below. The coefficient of f

Answers: 1

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

Which of the following components of a pid controlled accumulates the error over time and responds to system error after the error has been accumulated? a)- proportional b)- derivative c)- integral d)- on/off.

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Which of the following controllers anticipates the future from the slope of errors over time? a)-proportional b)-on/off c)-integral d)-derivative.

Answers: 2

Answer

Engineering, 04.07.2019 18:20

A3-mm-thick panel of aluminum alloy (k 177 w/m-k, c 875 j/kg-k and ? = 2770 kg/m) is finished on both sides with an epoxy coating that must be cured at or above t,-150°c for at least 5 min. the production line for the curing operation involves two steps: (1) heating in a large oven with air at ts,0-175°c and a convection coefficient of h, 40 w/m2. k, and (2) cooling in a large chamber with air at 25°c and a con- vection coefficient of he 10 w/m2.k. the heating portion of the process is conducted over a time interval te which exceeds the ime required to reach 150°c by 5 min (h = r + 300 s). the coating has an emissivity of ? = 0.8, and the temperatures of the oven and chamber walls are 175 and 25°c, respectively. if the panel is placed in the oven at an initial temperature of 25°c and removed from the chamber at a safe-to-touch tempera ture of 37°c, what is the total elapsed time for the two-step curing operation?

Answers: 3

Answer

Engineering, 04.07.2019 19:10

Tom is having a problem with his washing machine. he notices that the machine vibrates violently at a frequency of 1500 rpm due to an unknown rotating unbalance. the machine is mounted on 4 springs each having a stiffness of 10 kn/m. tom wishes to add an undamped vibration absorber attached by a spring under the machine the machine working frequency ranges between 800 rpm to 2000 rpm and its total mass while loaded is assumed to be 80 kg a) what should be the mass of the absorber added to the machine so that the natural frequency falls outside the working range? b) after a first trial of an absorber using a mass of 35 kg, the amplitude of the oscillation was found to be 10 cm. what is the value of the rotating unbalance? c) using me-3.5 kg.m, find the optimal absorber (by minimizing its mass). what would be the amplitude of the oscillation of the absorber?

Answers: 3

Answer

You know the right answer?

A block is sliding down an incline of 60 degrees as shown in the figure below. The coefficient of fr...

Questions