Engineering, 02.10.2020 14:01 diggy72

In an internal combustion engine, fuel is burned the engine. In the stroke of the four-stroke cycle, the piston rises, compressing the air-and-fuel mixture trapped in the combustion chamber.
In an engine, the stroke is the distance the piston .
When a piston is at its lowest position in the cylinder, it’s said to be at .
During the stage of engine operation, gases are released from the cylinder.
A four-stroke engine will contain at least two mechanical valves called the valve and the valve.
In the stroke of the four-stroke cycle, air mixed with fuel is drawn into the cylinder.
The total engine is stated as the volume of the space swept through by all the pistons.
A two-stroke engine completes all four stages of engine operation in four piston strokes.
During the stroke of the four-stroke cycle, the mixture of air and fuel is ignited, and the contained explosion of the fuel presses the piston back down in the cylinder.
The top of a cylinder is sealed by the cylinder .
The is the ratio of the total cylinder volume to the clearance volume.

Answers: 3

Show answers

Another question on Engineering

Engineering, 03.07.2019 14:10

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Ahot wire operates at a temperature of 200°c while the air temperature is 20°c. the hot wire element is a tungsten wire of 5 um diameter and 2 mm in length. plot using excel current, heat transfer and heat generated by the wire for air velocity varying from 1-10 m/s in steps of lm/s? matlab the sensor voltage output, resistance, or assume nu 0.989 re033pr13 take air properties at tr (200°c20°c)/2 = 110°c properties of tungsten: c 0.13 kj/kg.k 3 p 19250 kg/m k (thermal conductivity) = 174 w/m.k

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Vibration monitoring this technique uses the noise or vibration created by mechanical equipment and in seme cases by plant systems to detemine their actual condtion. a)- true b)- false

Answers: 2

Answer

You know the right answer?

In an internal combustion engine, fuel is burned the engine. In the stroke of the four-stroke cyc...

Questions