Engineering, 04.07.2020 14:01 182075

5.A non-cold-worked brass specimen of average grain size 0.01 mm has a yield strength of 150 MPa. Estimate the yield strength of this alloy after it has been heated to 500°C for 1000 s, if it is known that the value of σ0 is 25 MPa.

Answers: 3

Show answers

Answers

Answer from: shazaam1657

97.17 MPa

Explanation:

Given:-

- The nominal strength of the grain, σ0 = 25 MPa

- The average grain size of the brass specimen, d* = 0.01 m

- The yield strength of the non-cold worked specimen, σy = 150 MPa

- Conditions of cold-working: T = 500°C , t = 1000 s

Find:-

Estimate the yield strength of this alloy after cold - working process

Solution:-

- The nominal strength of the grain is a function of yield strength of the material, grain yield factor ( Ky ) and the grain size.

- the following relation is used to determine the grain strength:

σ0 = σy - ( Ky / √( d ) )

- We will use the above relation to determine the grain yield factor ( Ky ) for the alloy as follows. Note: here we will use the average value of grain size:

Ky = ( σy - σy )*√( d* )

Ky = ( 150 - 25 ) * √0.01

Ky = 12.5 MPa - √mm

- Now we will use the cold working conditions of T = 500 C and time of the process is t = 1000 s. We will look up the elongated size of the grain after the cold-working process in lieu with its yield factor ( Ky ). Use figure 7.25.

- The cold-worked grain size with the given conditions can be read off from the figure 7.25. The new size comes out to be d = 0.03 mm.

- We will again use the nominal grain strength relation expressed initially. And compute for the new yield strength of the cold-worked alloy.

σ0 = σy - ( Ky / √( d ) )

σy = σ0 + ( Ky / √( d ) )

σy = 25MPa + ( 12.5 / √( 0.03 mm ) )

σy = 97.17 MPa

- We see that the yield strength of the alloy decreases after cold-working process. This happens because the cold working process leaves with inter-granular strain ( dislocation of planes ) in the material structure which results from the increase in grain size.

Answer from: Quest

the clapeyron equation (also called the clausius-clapeyron equation) relates the slope of a reaction line on a phase diagram to fundamental thermodynamic properties.

explanation:

Answer from: Quest

answer:

the answer is d

explanation:

Another question on Engineering

Engineering, 04.07.2019 18:10

The filament of an incandescent lamp has a temperature of 2000k. calculate the fraction of radiation emitted in the visible light band if the filament is approximated as blackbody

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Which of the following controllers anticipates the future from the slope of errors over time? a)-proportional b)-on/off c)-integral d)-derivative.

Answers: 2

Answer

Engineering, 04.07.2019 19:20

Liquid flows at steady state at a rate of 2 lb/'s through a pump, which operates to raise the elevation of the liquid 100 ft from control volume inlet to exit. the liquid specific enthalpy at the inlet is 40.09 btu/lb and at the exit is 40.94 btub. the pump requires 3 btu/s of power to operate. if kinetic energy effects are negligible and gravitational acceleration is 32.174 tt/s, the heat transfer rate associated with this steady state process is most closely 1)-2,02 btu/s from the liquid to the surroundings 2)-3.98 btu/s from the surroundings to the liquid. 3)-4.96 btu/s from the surroundings to the liquid. 4)-1.04 btu/s from the liquid to the surroundings.

Answers: 2

Answer

Engineering, 04.07.2019 19:20

Acommercial grade cubical freezer, 4 m on a side, has a composite wall consisting of an exterior sheet of 5.0-mm thick plain carbon steel (kst= 60.5 w/m k), an intermediate layer of 100-mm thick polyurethane insulation (kins 0.02 w/m k), and an inner sheet of 5.0- mm thick aluminium alloy (kal polyurethane insulation and both metallic sheets are each characterized by a thermal contact resistance of r 2.5 x 104 m2 k/w. (a) what is the steady-state cooling load that must be maintained by the refrigerator under conditions for which the outer and inner surface temperatures are 25°c and -5°c, respectively? (b) for power saving purpose, which wall material should be increased/reduced in. thickness in order to reduce 50% of the cooling load found in part (a)? redesign the thickness of the proposed material. 177 w/m-k). adhesive interfaces between the q=575.93 w

Answers: 2

Answer

You know the right answer?

5.A non-cold-worked brass specimen of average grain size 0.01 mm has a yield strength of 150 MPa. Es...

Questions