![subject](/tpl/images/cats/User.png)
Engineering, 13.05.2020 05:57 hjlhdjfhjh
20-tooth spur pinion has a diametral pitch of 6 teeth/inch and a quality standard of No 6. When the pinion rotates at 1150 rev/min, the AGMA factors of safety for bending and contact are 3 and 5, respectively. (a) If the speed is increased to 2300 rev/min, what are the AGMA factors of safety for bending and contact? (b) Is bending or contact the primary failure mode for this gear? Provide evidence with calculated values
![ansver](/tpl/images/cats/User.png)
Answers: 3
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which of the following ziegler nichols tuning methods the response of the controller to a step input should exhibit an s-shaped curve? a)-open loop mode b)-closed loop mode c)-both modes (open & closed) d)-none of the modes (open & closed)
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Apiston-cylinder device contains 0.1 m3 of liquid water and 0.9 m3 of water vapor in equilibrium at 800 kpa. heat is transferred at constant pressure until the temperature of water reaches 350 °c. determine (a) the quality of water at the initial state (b) the work associated with this process, (c) the heat associated with this process.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
The maximum shear stress and maximum flexural stress occur at the same location along a beam subjected to a non-uniform bending load. a)-trune b)- false
Answers: 2
You know the right answer?
20-tooth spur pinion has a diametral pitch of 6 teeth/inch and a quality standard of No 6. When the...
Questions
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 29.04.2021 20:30
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 29.04.2021 20:30
![question](/tpl/images/cats/mat.png)
Mathematics, 29.04.2021 20:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 29.04.2021 20:30
![question](/tpl/images/cats/mat.png)
Mathematics, 29.04.2021 20:30
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 29.04.2021 20:30
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 29.04.2021 20:30