Engineering, 25.04.2020 02:59 anyar

A NC drill press is to perform a series of through-hole drilling operations on a 1.75 in thick aluminum plate that is a component in a heat exchanger. Each hole is 3/4 in diameter. There are 100 holes in all, arranged in a 10 by 10 matrix pattern, and the distance between adjacent hole centers (along the square) = 1.5 in. The cutting speed = 300 ft/min, the penetration feed (z-direction) = 0.015 in/rev, and the traverse rate between holes (x-y plane) = 15.0 in/min. Assume that x-y moves are made at a distance of 0.50 in above the work surface, and that this distance must be included in the penetration feed rate for each hole. Also, the rate at which the drill is retracted from each hole is twice the penetration feed rate. The drill has a point angle = 100°. Determine the time required from the beginning of the first hole to the completion of the last hole, assuming the most efficient drilling sequence will be used to accomplish the job.

Answers: 1

Show answers

Answers

Answer from: rireneb

The total time required is $T_{total}= 1601 sec$

Explanation:

From the question we are told that the

The thickness of the aluminium plate is $t = 1.75 \ in$

The diameter of the holes is $d = \frac{3}{4} \ in$

The number holes is n = 100

The pattern they arranged is = 10 by 10 matrix

The distance between the adjacent holes is $D = 1.5 \ in$

The cutting speed $v = 300 \ ft/min =300 *12 = 3600 \ in /min$

The penetration feed is $P = 0.015 \ in / rev$

The traverse rate is $T_r = 15.0 \ in /min$

The distance of the x-y moves $L = 0.50 \ in$

The rate at which the drill id retracted is R = 2P

The point angle of the drill is $\theta = 100^o$

Generally the cutting speed is mathematically represented as

$v = \pi d N$

Where N is the rotational speed

Substituting values

$3600 = \pi * \frac{3}{4} N$

=> $N = \frac{3600}{0.75 * 3.142 }$

$N = 1527.68 rev /min = \frac{1527.68}{60} = 25.46 \ rev /sec$

Now the feed rate is mathematically represented as

$Feed \ Rate [F] = P * N$

Substituting values

F = 0.015 * 25.46

$= 0.3819 \ in$

Next is to obtain the approach distance

The approach distance is mathematically represented as

$a = 0.5 * d * tan (90 - \frac{\theta }{2} )$

substituting values

$a = 0.5 * 0.75 * tan ({90 - \frac{100}{2} })$

$a = 2.5646 \ in$

also we are told that the drill x-y moves is 0.5 in above the work surface

Then the when retracting the drill the total distance moves is

Hence the total drill distance is w = 0.5 + 1.75 + 0.3146

$= 2.5646 \ in$

The time required to drill on hole is

$t_1 = \frac{w }{F }$

Substituting values

$t_1 = \frac{2.56446}{0.3819}$

= 6.71 sce

The retracting rate of the drill would be

K = 2P N

R = 0.015 * 2 * 25.46

= 0.7638

The time required to move the drill out of one hole is

$t_ 2 = \frac{w}{K}$

Substituting value

$t_2 = \frac{2.5646}{0.7638}$

$= 3.3576 \ sec$

The time required to move from one hole to another is

$t_3 = \frac{D}{T_r}$

$= \frac{1.5}{0.25}$

$= 6 \ sec$

The time it would take to perform the drilling of 100 holes is mathematically represented as

t_4 = 100 *t_1

= 6.71 *100

$= 671 \ sec$

Time required for retracting the drill from 100 holes is mathematically represented as

t_5 = 100 * t_2

t_5 = 3.3576 *100

= 336 sec

The time taken to move through the 100 holes is

t_6 = number of travers time * t_3

The number of trans verse time is = 99

t_6 = 99 * 6

$= 594 \ sec$

The time required the drilling task from the beginning of the first hole to the hole is

$T_{total } = t_4 + t_5 + t_6$

= 671 + 336 + 594

$T_{total}= 1601 sec$

Answer from: Quest

answer:

the army does care about its soilders sir i think yout getting off on the wrong foot sir you need to respect our country were keeping the peole that want to d harm towards you out. so dont go saying we don't care cause we do

Answer from: Quest

answer:

uygtfjyftujtfj

explanation:

Another question on Engineering

Engineering, 04.07.2019 18:10

Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Consider a large isothermal enclosure that is maintained at a uniform temperature of 2000 k. calculate the emissive power of the radiation that emerges from a small aperture on the enclosure surface. what is the wavelength ? , below which 10% of the emission is concentrated? what is the wavelength ? 2 above which 10% of the emission is concentrated? determine the wavelength at which maximum spectral emissive power occurs. what is the irradiation incident on a small object placed inside the enclosure?

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Apiston-cylinder device contains 0.1 m3 of liquid water and 0.9 m3 of water vapor in equilibrium at 800 kpa. heat is transferred at constant pressure until the temperature of water reaches 350 °c. determine (a) the quality of water at the initial state (b) the work associated with this process, (c) the heat associated with this process.

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Wiy doeres rere okhn a pump whon working betwon the same pressure range?

Answers: 2

Answer

You know the right answer?

A NC drill press is to perform a series of through-hole drilling operations on a 1.75 in thick alumi...

Questions