Engineering, 15.04.2020 03:03 torresq6647

A brass alloy is known to have a yield strength of 275 MPa (40,000 psi), a tensile strength of 380 MPa (55,000 psi), and an elastic modulus of 103 GPa (15.0×106 psi). A cylindrical specimen of this alloy 5.5 mm (0.22 in.) in diameter and 267 mm (10.52 in.) long is stressed in tension and found to elongate 7.0 mm (0.28 in.). On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If not, explain why.

Answers: 1

Show answers

Answers

Answer from: renaudciera

Computation of the load is not possible because E(test) >E(yield)

Explanation:

We are asked to ascertain whether or not it is possible to compute, for brass, the magnitude of the load necessary to produce an elongation of 7.0 mm (0.28 in.). It is first necessary/ important to compute the strain at yielding from the yield strength and the elastic modulus, and then the strain experienced by the test specimen. Then, if

E(test) is less than E(yield), deformation is elastic and the load may be computed. However is E(test) is greater than E(yield) computation/determination of the load is not possible even though defamation is plastic and we have neither a stress-strain plot or a mathematical relating plastic stress and strain. Therefore, we can compute these two values as:

Calculation of E(test is as follows)

E(test) = change in l/lo= Elongation produced/stressed tension= 7.0mm/267mm

=0.0262

Computation of E(yield) is given below:

E(yield) = σy/E=275Mpa/103 ×10^6Mpa= 0.0027

Therefore, we won't be able to compute the load because for computation to take place, E(test) <E(yield). In this case, E(test) is greater than E(yield).

Answer from: kamraaa

It's not possible to compute the magnitude of the load

Explanation:

Given data:

Yield strength = 275Mpa

Tensile strength = 380Mpa

Elastic modulus = 103Gpa = 103 * 1000MPa

Diameter = 5.5 mm

Length = 267 mm

Elongation = 7.0 mm

Calculating the strain test value using the formula'

ε(test) = ΔL/Lo

Substituting, we have

ε = 7.0/267

= 0.0262

Calculating the yield strain using the formula

ε(yield) = бy/E

Substituting, we have

ε(yield) = 275/ 103 * 1000

= 275/103000

= 0.00267

From the calculation above, the strain test is greater than the yield. Therefore, it's not possible to compute the magnitude of the load.

ε(test) ⊃ ε(yield)

Answer from: Quest

this is true

explanation:

i looked it up

Answer from: Quest

answer:

make you upset

explanation:

Another question on Engineering

Engineering, 04.07.2019 18:10

Afluid flows with a velocity field given by v=(x/t)i.. determine the local and convective accelerations when x=3 and t=1.

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Shafts are machine elements that are used to a) carry axial loads b) direct shear loads c) transmit power d) rotate at constant speed e) none of the above circular and square shafts subjected to the same torque under the same circum behave a) the same way b) almost the same way

Answers: 2

Answer

Engineering, 04.07.2019 18:10

True or false (explain) (110)[111] is a slip system in bcc metals . the {111} family in fcc contains 8 planes. resolved shear stress (rss) in single crystals is just related to the applied stress. critical resolved shear stress (crss) in single crystal metals is direct proportional to the number of defects in the structure

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Which from the following instrument is commonly used to detect the high pitch butzing sound in bearings? [clo4] a)-digital ultrasonic meter b)-infrared camera c)-spectroscopic d)-vibrometer

Answers: 2

Answer

You know the right answer?

A brass alloy is known to have a yield strength of 275 MPa (40,000 psi), a tensile strength of 380 M...

Questions