Engineering, 25.02.2020 17:53 Nickanderson21

A Diesel cycle engine is analyzed using the air standard method.
Given the conditions at state 1, compression ratio (r), and cutoff ratio (rc) determine the efficiency and other values listed below.
Note: The specific heat ratio and gas constant for air are given as k=1.4 and R=0.287 kJ/kg. K respectively.

T1 (K) = 328
P1 (kPa) = 190
r = 14
rp = 1.3
rc = 1.3

a) Determine the specific internal energy (kJ/kg) at state 1.
b) Determine the relative specific volume at state 1.
c) Determine the relative specific volume at state 2.
d) Determine the temperature (K) at state 2.
e) Determine the pressure (kPa) at state 2.
f) Determine the specific enthalpy (kJ/kg) at state 2.
g) Determine the temperature (K) at state 3.
h) Determine the pressure (kPa) at state 3.
i) Determine the specific enthalpy (kJ/kg) at state 3.
j) Determine the relative specific volume at state 3.
k) Determine the relative specific volume at state 4.
l) Determine the temperature (K) at state 4.
m) Determine the pressure (kPa) at state 4.
n) Determine the specific internal energy (kJ/kg) at state 4.
o) Determine the net work per cycle (kJ/kg) of the engine.
p) Determine the heat addition per cycle (kJ/kg) of the engine.
q) Determine the efficiency (%) of the engine.

Answers: 1

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

Ahot wire operates at a temperature of 200°c while the air temperature is 20°c. the hot wire element is a tungsten wire of 5 um diameter and 2 mm in length. plot using excel current, heat transfer and heat generated by the wire for air velocity varying from 1-10 m/s in steps of lm/s? matlab the sensor voltage output, resistance, or assume nu 0.989 re033pr13 take air properties at tr (200°c20°c)/2 = 110°c properties of tungsten: c 0.13 kj/kg.k 3 p 19250 kg/m k (thermal conductivity) = 174 w/m.k

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Inspection for bearing condition will include: (clo4) a)-color b)-smell c)-size d)-none of the above

Answers: 1

Answer

Engineering, 04.07.2019 19:20

Air at a pressure of 1atm and a temperature of 40 c is in parallel flow over the top surface of a flat plate that is heated to a uniform temperature of 120 c. the plate has a length of 0.40m (in the flow direction) and a width of 0.15m. the reynolds number based on the plate length is 50, 000. what is the rate of heat transfer from the plate to the air? if the free stream velocity of the air is doubled and the pressure is increased to 10 atm what is the rate of heat transfer?

Answers: 2

Answer

Engineering, 06.07.2019 04:10

Aheat pump using refrigerant-134a heats a house by using underground water at 8°c as the heat source. the house is losing heat at a rate of 60,000 kj/h. the refrigerant enters the compressor at 280 kpa and 0°c, and it leaves at 1 mpa and 60°c. the refrigerant exits the condenser at 30°c. determine: (a) the power input to the heat pump, (b) the rate of heat absorption from the water, and (c) the increase in electric power input if an electric resistance heater is used instead of a heat pump

Answers: 2

Answer

You know the right answer?

A Diesel cycle engine is analyzed using the air standard method.
Given the conditions at stat...

Questions