Engineering, 14.02.2020 21:57 screamqueen

A plate (A-C) is connected to steelflat bars by pinsat A and B. Member A-E consists of two 6mm by 25mm parallel flat bars. At C, plate A-C is supported by a19mm-diameter pin (double shear). Find the axial stress in AE and the shear stress in pin C.

Answers: 1

Show answers

Answers

Answer from: jordand7514

stress_ac = 5.333 MPa

shear stress_c = 1.763 MPa

Explanation:

Given:

- The missing figure is in the attachment.

- The dimensions of member AC = ( 6 x 25 ) mm x 2

- The diameter of the pin d = 19 mm

- Load at point A is P = 2 kN

Find:

- Find the axial stress in AE and the shear stress in pin C.

Solution:

- The stress in member AE can be calculated using component of force P along the member AE as follows:

stress_ac = P*cos(Q) / A_ae

Where, Angle Q: A_E_B and A_ac: cross sectional area of member AE.

cos(Q) = 4 / 5 ..... From figure ( trigonometry )

A_ae = 0.006*0.025*2 = 3*10^-4 m^2

Hence,

stress_ae = 2*(4/5) / 3*10^-4

stress_ae = 5.333 MPa

- The force at pin C can be evaluated by taking moments about C equal zero:

(M)_c = P*6 - F_eb*3

0 = P*6 - F_eb*3

F_eb = 0.5*P

- Sum of horizontal forces for member AC is zero:

P - F_eb - F_c = 0

F_c = 0.5*P

- The shear stress of double shear bolt is given by an expression:

shear stress = shear force / 2*A_pin

Where, The area of the pin C is:

A_pin = pi*d^2 / 4

A_pin = pi*0.019^2 / 4 = 2.8353*10^-4 m^2

Hence,

shear stress = 0.5*P / 2*A_pin

shear stress = 0.5*2 / 2*2.8353*10^-4

shear stress = 1.763 MPa

A plate (A-C) is connected to steelflat bars by pinsat A and B. Member A-E consists of two 6mm by 25

Answer from: Quest

do you have any options?

Answer from: Quest

Oh yes igger daddy filled my loose ahοle with your sweet sweet mсum said ronald mcdonald as he spread his sesame covered mcahοle for thanos. thanos slid his throbbing purple ᑕock in to ronald's a. o screamed ronald as he poor hole was torn to bloody shreds. gunga gingagunga gingagunga gingagunga ginga a space ranger appeared making autistuc noises odio a los negros! said buzz lightyear as he aped them both.

Another question on Engineering

Engineering, 04.07.2019 18:10

Water at 70°f and streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream. 0 psia is heated in a chamber by mixing it with saturated water vapor at 20 psia. if both streams enters the mixing chamber at the same mass flow rate, determine the temperature and the quality of the existing system.

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the water level in the tank, through a 2.2-cm-internal-diameter pipe by maintaining a constant air pressure of 300 kpa (gage) in the tank. if the head loss in the piping is 2 m of water, determine the discharge rate of the supply of water to the roof top in liters per second.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

The higher the astm grain size number, the finer the gran is. a)-true b)-false

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Asimple rankine cycle uses water as the working fluid. the water enters the turbine at 10 mpa and 480c while the condenser operates at 6 kpa. if the turbine has an isentropic efficiency of 80 percent while the pump has an isentropic efficiency of 70 percent determine the thermal efficiency

Answers: 1

Answer

You know the right answer?

A plate (A-C) is connected to steelflat bars by pinsat A and B. Member A-E consists of two 6mm by 25...

Questions