![subject](/tpl/images/cats/User.png)
Engineering, 09.11.2019 07:31 quintonps12
You will write a simplified model of a bouncing ball using numpy. assume the ball is dropped on earth under constant acceleration g=9.81ms2 from the limit of its atmosphere, a height of 250km. model the ball's motion for one hour and 15 minutes (include second 0 and second 4,500 in your data points). after the initial state, simulate 5,000 updates to the state (for a total of 5,001 points.) your simulation should use float64 numpy arrays for time (t) and height (y). time should be represented in seconds and height should be represented in meters.
![ansver](/tpl/images/cats/User.png)
Answers: 1
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
At 12 noon, the count in a bacteria culture was 400; at 4: 00 pm the count was 1200 let p(t) denote the bacteria cou population growth law. find: (a) an expression for the bacteria count at any time t (b) the bacteria count at 10 am. (c) the time required for the bacteria count to reach 1800.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Water at the rate of 1 kg/s is forced through a tube with a 2.5 cm inner diameter. the inlet water temperature is 15°c, and the outlet water temperature is 50°c. the tube wall temperature is 14°c higher than the local water temperature all along the length of the tube. what is the length of the tube?
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200°c and outer surface temperature of the insulation to be 15°c. calculate the thickness of insulation required.
Answers: 3
You know the right answer?
You will write a simplified model of a bouncing ball using numpy. assume the ball is dropped on eart...
Questions
![question](/tpl/images/cats/biologiya.png)
Biology, 14.12.2021 14:20
![question](/tpl/images/cats/en.png)
English, 14.12.2021 14:20
![question](/tpl/images/cats/en.png)
English, 14.12.2021 14:30
![question](/tpl/images/cats/mat.png)
Mathematics, 14.12.2021 14:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 14.12.2021 14:30
![question](/tpl/images/cats/User.png)
![question](/tpl/images/cats/fizika.png)
Physics, 14.12.2021 14:30
![question](/tpl/images/cats/mkx.png)
Arts, 14.12.2021 14:30
![question](/tpl/images/cats/biologiya.png)
Biology, 14.12.2021 14:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 14.12.2021 14:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 14.12.2021 14:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/geografiya.png)
Geography, 14.12.2021 14:30
![question](/tpl/images/cats/fr.png)
French, 14.12.2021 14:30
![question](/tpl/images/cats/health.png)
Health, 14.12.2021 14:30
![question](/tpl/images/cats/mat.png)
Mathematics, 14.12.2021 14:30