![subject](/tpl/images/cats/User.png)
Engineering, 18.10.2019 20:30 artiomtyler007
Alarge (w > > a) plate sample containing an edge (surface) crack with an initial length of 0.010mm is subjected to two sets of uniaxial cyclic (sinusoidal) fatigue loading. the first set of cyclic loading varies between +25 and +125 mpa for 350,000 cycles. the second set of loading varies between +250 and ‐250 mpa. assume the material has a plane strain fracture toughness of 25 mpa m 1/2 and paris law material constants n= 3.1 and c = 1.8x10‐10 for the units given here.
![ansver](/tpl/images/cats/User.png)
Answers: 2
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aflywheel accelerates for 5 seconds at 2 rad/s2 from a speed of 20 rpm. determine the total number of revolutions of the flywheel during the period of its acceleration. a.5.65 b.8.43 c. 723 d.6.86
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Find the minimum film thickness for a journal bearing with the data below. shaft diameter, d-50 mm, clearance ratio, cdratio? 0.001, shaft speed, n 2000 rpm; bearing length. i 200 mm; eccentricity ration, ? -0.55. ( note, cdratio-ca/d) the minimum film thickness is um
Answers: 2
You know the right answer?
Alarge (w > > a) plate sample containing an edge (surface) crack with an initial length of 0....
Questions
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 06.05.2020 18:58
![question](/tpl/images/cats/mat.png)
Mathematics, 06.05.2020 18:58
![question](/tpl/images/cats/mat.png)
Mathematics, 06.05.2020 18:58
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 06.05.2020 18:58
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
English, 06.05.2020 18:58
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 06.05.2020 18:58
![question](/tpl/images/cats/istoriya.png)
History, 06.05.2020 18:58
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 06.05.2020 18:58