Computers and Technology, 31.05.2021 06:50 gutierrezforlife8220

A) i) Describe the all pins of 82C55 programmable interface (PPI) IC. ii) Define command byte A & B of the command register in the 82C55 IC.
iii) Draw the proper circuit diagram of an 8-digit LED display interfaced to 8088
microprocessor through an 82C55 IC.

Answers: 1

Show answers

Another question on Computers and Technology

Computers and Technology, 21.06.2019 22:00

Some of your friends have gotten into the burgeoning field of time-series data mining, in which one looks for patterns in sequences of events that occur over time. purchases at stock exchanges"what's being bought" are one source of data with a natural ordering in time. given a long sequence s of such events, your friends want an efficient way to detect certain "patterns" in them"for example, they may want to know if the four events buy yahoo, buy ebay, buy yahoo, buy oracle occur in this sequence s, in order but not necessarily consecutively. they begin with a collection of possible events (e.g., the possible transactions) and a sequence s of n of these events. a given event may occur multiple times in s (e.g., yahoo stock may be bought many times in a single sequence s). we will say that a sequence s is a subsequence of s if there is a way to delete certain of the events from s so that the remaining events, in order, are equal to the sequence s . so, for example, the sequence of four events above is a subsequence of the sequence buy amazon, buy yahoo, buy ebay, buy yahoo, buy yahoo, buy oracle their goal is to be able to dream up short sequences and quickly detect whether they are subsequences of s. so this is the problem they pose to you: give an algorithm that takes two sequences of events"s of length m and s of length n, each possibly containing an event more than once"and decides in time o(m + n) whether s is a subsequence of s.

Answers: 3

Answer

Computers and Technology, 23.06.2019 02:30

Research data that is presented using descriptive language is said to be

Answers: 2

Answer

Computers and Technology, 23.06.2019 15:30

Write a program in plp assembly that counts up by one starting from zero (or one) inside a loop and writes this value to the leds every time the value is increased. the memory address of the leds is 0xf0200000. the table below shows the meaning and an example usage of the instructions covered in the video, plp instructions for project 1. instruction example usage meaning load immediate li $t0, 8 register $t0 is set to the value, 8. store word sw $t2, 0($t1) the value in register $t1 is used as the memory address. the value in register $t2 is copied into this memory address. add addiu $t4, $t3, 29 register $t4 is assigned the sum of 29 and the value in register $t3. jump j your_label_name the program jumps to the line following the label, "your_label_name: ". label your label name: defines a label called "your_label_name: " that can be jumped to

Answers: 2

Answer

Computers and Technology, 23.06.2019 19:00

Write a program that displays the following menu: geometry calculator 1. calculate the area of a circle 2. calculate the area of a rectangle 3. calculate the area of a triangle 4. quit enter your choice (1-4): if the user enters 1, the program should ask for the radius of the circle and then display its area. use the following formula: area = ď€(the square of r) use 3.14159 for ď€ and the radius of the circle for r. if the user enters 2, the program should ask for the length and width of the rectangle and then display the rectangleâ€™s area. use the following formula: area = length * width if the user enters 3, the program should ask for the length of the triangleâ€™s base and its height, and then display its area. use the following formula: area = base * height * .5 if the user enters 4, the program should end. input validation: display an error message if the user enters a number outside the range of 1 through 4 when selecting an item from the menu. do not accept negative values for the circleâ€™s radius, the rectangleâ€™s length or width, or the triangleâ€™s base or height. note: if the user enters an improper menu choice (1-4), the program prints "the valid choices are 1 through 4. run the program again and select one of those." if the user enters a negative radius, the program prints "the radius can not be less than zero." if the user enters a negative value for height or base, the program prints "only enter positive values for base and height."

Answers: 1

Answer

You know the right answer?

A) i) Describe the all pins of 82C55 programmable interface (PPI) IC. ii) Define command byte A &am...

Questions