Computers and Technology, 04.04.2020 10:24 abelgutierrez370

A router receives a packet and determines the outbound link for the packet. When the packet arrives, 2/3 of one other packet is done being transmitted on this outbound link and five other packets are waiting to be transmitted. Packets are transmitted in order of arrival. Suppose all packets are 3,000 bytes, and the link rate is 4 Mbps. What is the queuing delay for the packet

Answers: 1

Show answers

Answers

Answer from: maggie3541

Queuing Delay is 0.08 seconds

Explanation:

The answer follows a formula that is relatively easy to use and is detailed below.

Queuing Delay = [(L - x) + (nL)] / R

where,

L is packet length given as 3,000 bytes

x is the currently transmitted packet given as 2/3 * 3,000 = 2,000

n is the number of packets waiting in the Que given as 5

R is the rate of transmission given as 4 Mbps (4 * 10^6 Bps)

We can simply plug in the above information in the equation for computing Queuing Delay.

Lets take the numerator first which would be [(3000 - 2000) + (5 * 3000)]

The numerator would be 16000 bytes. These are being transmitted at 4Mbps. So, 16000*4*5 = 320,000 "bits"

Queuing Delay= 320,000/4000000

Queuing Delay = 0.08 seconds.

As we can see, the formula is quite intuitive to use. You are simply taking the number of packets to be transmitting, incorporating the partially transmitted packet, multiplying by the number of packets and the rate of transmission and then dividing the product by the rate of transmission to compute what the delay in the Que is.

Answer from: Quest

hey! im not 100 percent sure but im pretty sure that what you want to do is not possible : (

explanation:

Answer from: Quest

Through the process of sedimentation,sediment is turned back to rock to form sedimentation.the process of sedimentation is: > deposition-where fragments were deposited into the river or sea under gravity or travelling agent such as wind or water. > sedimentation-the fragments deposited in the river sedimented and accumulate> compaction-the layers of fragments deposited undergoes compaction due to the weight if the upper layers> cementation-chemical substance of the fragments such as cement dissolved into the water and cement the other fragments together to form sedimentary rock.thus,cementation and compaction are the process.on the other hand, transformation only occur when a rock under goes metamorphism(compaction or extreme heat).while recrystillization occurs when a rock is melted and cooled down,which also requires metamorphism to take place.hope it !

Another question on Computers and Technology

Computers and Technology, 22.06.2019 03:00

Consider this data sequence: "3 11 5 5 5 2 4 6 6 7 3 -8". any value that is the same as the immediately preceding value is considered a consecutive duplicate. in this example, there are three such consecutive duplicates: the 2nd and 3rd 5s and the second 6. note that the last 3 is not a consecutive duplicate because it was preceded by a 7. write some code that uses a loop to read such a sequence of non-negative integers , terminated by a negative number. when the code finishes executing, the number of consecutive duplicates encountered is printed. in this case, 3 would be printed. assume the availability of a variable, stdin, that references a scanner object associated with standard input. that is, stdin = new scanner(system.in); is given.

Answers: 1

Answer

Computers and Technology, 23.06.2019 19:30

Of the following pieces of information in a document, for which would you most likely insert a mail merge field?

Answers: 3

Answer

Computers and Technology, 24.06.2019 18:30

In what way is your social media footprint related to your digital id

Answers: 1

Answer

Computers and Technology, 25.06.2019 01:30

Ashort circuit locator should be periodically run along the cords used in a shop to check for shorts and open circuits. a.)true b.)false