Two molecules have the same molecular geometry but different electron domain geometries. which combination of atoms and lone pairs around the central atom could describe these molecules? 2 atoms and 2 lone pairs; 3 atoms and 0 lone pairs 1 atom and 3 lone pairs; 2 atoms and 1 lone pair 3 atoms and 1 lone pair; 3 atoms and 0 lone pairs 2 atoms and 2 lone pairs; 2 atoms and 1 lone pair

The correct answer is:
2 atoms and 2 lone pairs; 2 atoms and 1 lone pair.
Both AX₂E₂ and AX₂E have different electron domain geometry; AX₂E₂ is tetrahedral and AX₂E is trigonal planar but both of them has the same molecular geometry Bent

Answer : The correct option is, 2 atoms and 2 lone pairs; 2 atoms and 1 lone pair

Explanation :

In type , when bond pair of electrons is 2 and lone pair of electrons is 1 then the electron domain geometry is Trigonal planar and molecular geometry is Bent.

In type , when bond pair of electrons is 2 and lone pair of electrons is 2 then the electron domain geometry is Tetrahedral and molecular geometry is Bent.

Hence, a molecule having 2 atoms and 2 lone pair have the same molecular geometry as that of the molecule having 2 atoms and 1 lone pair.

The table is shown below.

Answerthe half-reaction having the greatest tendency to occur at the anode:     i₂(aq) + 2e⁻  ⇄ 2i⁻  ;   e = +0.53 v======oxidation occurs at the anode. we must therefore find the half-reaction with the greatest tendency to oxidize.the given values of e are reduction potentials (the form of the half-reactions are of reduction).the lower the reduction potential, the higher the potential to oxidize. the half-cell with the lowest reduction potential will have the greatest tendency to oxidize at the anode.the half-reaction having the greatest tendency must be    i₂(aq) + 2e⁻  ⇄ 2i⁻    e = +0.53 vbecause its reduction potential is the lowest out of the three.

Note that 2 mol dm⁻³ = 2 mol/(dm³)outline: we're given the concentration of hcl, which is  2 mol dm⁻³ (cubic meters in the denominator can represent volume, so i know this is concentration). we're an amount of calcium carbonate caco₃, which is 5 g. we're presented with a chemical equation which includes caco₃ and hcl. we are told to find the volume of hcl. from what we see so far, this seems to be a stoichiometry  problem. we'll have to use the given information about calcium carbonate to find the amount of moles of hcl needed to fully react with calcium carbonate. then we'll have information about the moles of hcl and the concentration of hcl; that will be enough to figure out volume according to the formula concentration = moles / volume.======all the answer choices are not in dm.convert the given concentration so that it uses cm⁻³.we can use conversion factors. we have to cube our conversion factors so that dimensional analysis works.we can convert to meters first, using the fact that     10 dm = 1 m  ⇔ 10³ dm³ = 1 m³then we use the fact that     10² cm = 1 m ⇔ (10² cm)³ = (1 m)³ ⇔ 10⁶ cm³ = 1 m³so converting:     now we have to find the moles of hydrochloric  acid neededfind the moles of calcium carbonate. we have to find the molar mass of calcium carbonate, caco₃, which can be found by    molar mass = (mass ca) + (mass c) + 3(mass o)    = 40 + 12 + 3(16)    = 100 g/molconvert the given 5 g to moles:     mol caco₃ = 5 g caco₃ * 1 mol/(100 g) = 0.05 mol caco₃use stoichiometry (ratios) to figure out the moles of hcl needed. ratio wise, there's 2 hcls for every caco₃, so use dimensional analysis    mol hcl = mol caco₃ * (2 mol hcl) / (1 mol caco₃)    = 0.05 mol hcl * 2    = 0.1 mol hcl  we have 0.1 mol hcl and concentration of hcl (0.002 mol/cm³).we need to find volumesince concentration = moles / volume, rearrange to get     volume = moles / concentration    volume = 0.1 mol / (0.002 mol/cm³)    volume = 50 cm³