subject

Chemistry, 31.01.2022 14:00 enrique764058

A chip bag has a volume of 0.91 L when the pressure is 28.8 psi. What is the pressure if the volume is 10.39 L?

ansver

Answers: 3

Show answers

Another question on Chemistry

question

Chemistry, 21.06.2019 19:00

Apeak with a retention time of 407 s has a width at half-height (w1/2) of 7.6 s. a neighboring peak is eluted 17 s later with a w1/2 of 9.4 s. a compound that is known not to be retained was eluted in 2.5 s. the peaks are not baseline resolved. how many theoretical plates would be needed to achieve a resolution of 1.5?

Answers: 2

question

Chemistry, 22.06.2019 03:30

What is the number of moles of chemical units represented by 9.03x10^24? and how do i show work? (dumb it down )

Answers: 1

question

Chemistry, 22.06.2019 05:30

Why is soap used to remove grease? a. its nonpolar end dissolves the grease. b. it makes the water bond with the grease. c. it chemically bonds with the grease. d. its polar end dissolves the grease.correct answer for apex - a, its nonpolar end dissolves the grease.

Answers: 1

question

Chemistry, 22.06.2019 12:00

What is a possible quantum number set for an electron in the 3s orbital of a magnesium atom

Answers: 1

You know the right answer?

A chip bag has a volume of 0.91 L when the pressure is 28.8 psi. What is the pressure if the volume...

Questions

question

Chemistry, 14.09.2019 01:10

Let's assume you have infinite amount of dilute aqueous solution of gold that only contains gold at a concentration of 1x10.10weight raction. if you w...

question

Engineering, 14.09.2019 01:10

When is it appropriate to model a structural element as a beam?...

question

Engineering, 14.09.2019 01:10

Astrain gauge with a 4 mm gauge length gives a displacement reading of 1.5 um. calculate the stress at the location of the strain gauge if the materia...

question

Engineering, 14.09.2019 01:10

What are the principal advantages of dic over strain gauges?...

question

Engineering, 14.09.2019 01:10

When there is no flow, the signal transit times between ultrasonic sensor pairs are x upstream and downstream. a. not applicable b. same c. different...

question

Engineering, 14.09.2019 01:10

The frequency of the changing zones of pressure corresponds to the x of passing vortices....

question

Engineering, 14.09.2019 01:10

Total flow can be calculated since the distance between two consecutive vortices corresponds to a defined volume....

question

Engineering, 14.09.2019 01:10

Specific internal energy is measured in energy per unit mass dimensions. what is 310 kj/kg in btu/lbm units?...

question

Engineering, 14.09.2019 01:10

The differential transit times of the signals going upstream and downstream is a direct measure of (x)....

question

Engineering, 14.09.2019 01:10

Using a coriolis meter is the only way the particular x of mass flow, density, volume flow, and flow velocity can be measured simultaneously. a. proce...

question

Engineering, 14.09.2019 01:10

It is critical to the measurement that any flow meter is installed in such a manner that is kept full of fluid at all times. a) true b) false...

question

Engineering, 14.09.2019 01:10

When sensors in this kind of flow meter sense a change in tube oscillation what is this phenomena called?...

question

Engineering, 14.09.2019 01:10

Laminar flow is the most desirable for flow measurements in pipes. a) true b) false...

question

Engineering, 14.09.2019 01:10

A1 m thick wall is made of concrete with a thermal conductivity of 1 w/m/k. there are temperature sensors on the wall's surface and buried within the...

question

Engineering, 14.09.2019 01:10

When piping systems contain bends in multiple directions in succession....

question

Engineering, 14.09.2019 01:10

Seawater has a specific density of 1.025. what is its specific volume in m^3/kg (to 3 significant figures of accuracy, tolerance +/- 0.5 m^3/kg)?...

question

Engineering, 14.09.2019 01:10

The amount of energy required to maintain the desired temperature difference is proportional to the cooling effect, and therefore, it is a direct meas...

question

Engineering, 14.09.2019 01:10

Thermal meters use principles of x in order to determine various flow process variables. a. fluid dynamics b. heat generation c. heat transfer d. ther...

question

Engineering, 14.09.2019 01:10

Acylindrical smokestack is 26 m high and has an average diameter of 4 m. for a wind speed past the smokestack of 1.5 m/s, determine the drag force exe...

question

Physics, 14.09.2019 01:10

Aplacekicker must kick a football from a point 36.0 m (about 40 yards) from the goal. half the crowd hopes the ball will clear the crossbar, which is...

More questions: Chemistry Another questions

Questions on the website: 13722360